China factory elevator painting/ powder coating booth
The coating line consists of a surface pre-treatment machine, a
drying and curing oven, powder coating, a curing drying tunnel, a
hanging conveyor, and an electrical control system. Sprinkler
System The spray device is composed of a spray pump, a pressure
relief valve, a pressure gauge, a spray main pipe, a spray riser
and a universal ball nozzle. The flow rate and pressure of each
pump can be adjusted through the throttle adjustment valve and
pressure gauge, and the pressure adjustment range is 0.5 ~ 1.5Kg.f
/ cm2 The spray main is made of stainless steel pipe; the spray
riser is made of stainless steel pipe. The film spraying section
adopts W-type atomizing nozzles, and the remaining spraying
sections adopt V-type nozzles. The total amount of nozzles is 960.
The nozzle is made of polypropylene and has a heat resistance and
chemical stability. The liquid storage tank is provided with alarms
for the liquid level above and below, and is interlocked with the
spray pump. Storage tank blowdown valve stainless steel wafer type
butterfly valve. Tank The inner panel of the tank is δ2.0mm thick
SUS304, and the outer panel of all tanks is δ0.8mm thick SUS304.
The inside and outside of the heating tank are insulated by 50mm
thick high-quality rock wool, which has good insulation
performance. All tanks are equipped with double stainless steel 10
mesh screen filters. Between the pre-greasing and main degreasing
tanks, water washing1 and pure water washing 1, a connecting pipe
is provided, and a DN65 galvanized steel pipe is used. The
countercurrent water replenishment method can improve the cleaning
effect and save resources. There are two slopes at the bottom of
all tanks, which can completely discharge the slag in the tank. The
inner plates of the tank are all through welding, and after the
water loading test, it is ensured that the welding is firm and does
not leak. The membrane tank is equipped with a set of 90 ton/hour
bag filters. Pump system This system is equipped with 6 pumps. The
outlet of the spray pump body is provided with a pressure relief
bypass, and the pump flow and pressure are adjusted by a bypass
valve. Valves and fittings The stainless steel spray line uses
stainless steel valves. A copper ball valve is used for the water
pipe. The pre-treatment spray branch pipe is connected with the
riser by a union. The connection between the pretreatment
supervisor and the supervisor, and between the supervisor and the
pump are flanged and bolted. All pipes can be easily removed.
Auxiliary equipment The pre-degreasing tank is equipped with a set
of the oil-water separator to remove the oil stains in the
pre-degreasing tank and effectively control the composition of the
tank liquid. relatively stable. A set of pipelines for driving the
degreasing tank liquid into the pre-greasing tank is also provided.
The silane tank is equipped with a set of automatic liquid adding
device, the main configuration is as follows: PH meter × 1 unit and
metering pump × 1 unit (preferred brand: Pasfida), and the medicine
is automatically added, which is a closed-loop system. The silane
tank is equipped with a stainless steel bag filter to remove
impurities in the tank and improve the utilization rate of the tank
liquid. All tanks are equipped with a lower limit alarm system to
prevent dry liquid from damaging the main spray pump. Rotor
flowmeters are all installed in the fresh pure water direct
injection pipelines, which can easily observe the specific water
consumption. The rotor flowmeters use domestic high-quality brands.
There is an artificial water blowing platform (1) and a compressed
air blowing gun at the pre-treatment outlet. Pure water equipment
1. R / O terminal water output of primary reverse osmosis system:
2.5 tons/hour. 2. Outlet conductivity of reverse osmosis system:
less than 20us / cm. 3. Raw water quality: The buyer provides a
water quality report. 4. System recovery rate: about 70%. 5.
Process flow: Raw water → raw water pump → multi-media filter →
activated carbon filter → precision filter → high-pressure pump →
reverse osmosis R / O device → Terminal water tank → Terminal water
pump → Process water GEMA Manual Spray Gun Wear-resistant unit for
coating of difficult geometries State-of-the art design and high
performance materials guarantee excellent powder distribution and
best coating results for application of abrasive enamel powder.
OptiGun® Automatic Gun: efficient and reliable OptiGuns offer the
highest transfer efficiency, perfect quality in every application
and are the ideal solution for color change. Detailed Images Gun
nozzle design Powder coating requires a perfect combination of
nozzle design and high voltage supply to achieve an homogeneous
powder cloud. • The high voltage field plays a very important role
ensuring a perfect powder atomization and charging. • Different
object geometries to be coated require different nozzle ge
Related products about China Factory Elevator Painting/ Powder Coating Booth
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup