0.5mm/1mm/1.5mm/2mm 500 Microns High Density Black HDPE Geomembrane for Fish Pond/Agriculture/Dam/Landfill/Lake/Biogas/Aquaculture Project

0.5mm/1mm/1.5mm/2mm 500 Microns High Density Black HDPE Geomembrane for Fish Pond/Agriculture/Dam/Landfill/Lake/Biogas/Aquaculture ProjectProduct Description HDPE GeomembraneHDPE Geomembrane is the low permeable synthetic geomembrane liner and geotechnical engineering materials which are widely used for acquanculture and water containment applications. HDPE Geomembrane is made of finest quality high density polyethylene (HDPE) with specially formulated, virgin polyethylene resin, combined with specified quantity carbon black, antioxidant, anti-aging agent and UV resistance components, which makes our smooth geomembrane HDPE Geomembrane with excellent resistance to UV radiation and is suitable for exposed conditions. HDPE Geomembrane is the ideal low permeable synthetic material for Shrimp farming.Product ParametersHDPE Geomembrane SpecificationItemTest ValueRH0.30mmRH0.5mmRH0.75mmRH1.0mmRH1.5mmRH2.0mmRH3.0mmMinimum Density(g/cm³)                    0.94Strength at yield,N/mm581115222944Strength at break ,N/mm8142028405380Elongation at yield,%13Elongation at break,%720minTear Resistance N406593125190250375Puncture Resistance N105176240320480640960Stress Crack Resistance, hrs300Carbon Black Content, %2.0-3.0Carbon Black Dispersion1 or 2Standard OIT Min100High Pressure OIT Min40085ºC Heat aging(OIT Retention rate at Normal pressure after 90d ) %85UV resistance (OIT retention rate after 1600 hours of UV radiation)65Impact Cold Crack at -70°CPassWater vapor permeability(g.cm/cm2 .s.Pa)≤1.0×10-13Dimensional Stability (%)±2Production FlowHDPE Geomembrane Production Application  HDPE Geomembrane Application 1.Landfill Foundation and Landfill Caps 2.Toxic Waste Containment 3.Liquid Waste Containment 4.Aquaculture Ponds 5.Drainage Pipeline 6.Water Reservoir 7.Dam Mining/Tailing Works 8.Tunnel Lining 9.Lake and Reservoir lining 10.Prevent contaimation of ground water 11.Municipal waste management 12.Hazardous waste management 13.Wastewater containment lagoons 14.Traffic facilities  HDPE Geomembrane Features 1.High anti-seepage coefficient (1×10-17cm/s) 2.High tensile strength. High tear resistance 3. Good flexibility and elasticity, adapt to uneven geological settlement 4.Resistant to strong acid, alkali, and oil corrosion, with excellent chemical corrosion resistance 5.Good heat resistance and cold resistance.  With wide applicability to climatic conditions 6.Resistance to ultraviolet radiation. Good anti-aging performance 7.Environmental protection, high-quality virgin plastic and carbon black particles do not contain any preservatives and do not pollute water and soil 8.Easy to weld, easy to install and construct. 9.Cost-effective   Geomembrane installationHDPE GEOMEMBRANE WELDING & INSTALLATION-- The surface must be inspected immediately before the liner is placed. Any debris that could damage the liner or prevent an even/smooth deployment must be removed.-- The deployment of the rolls should be in a manner that will require the least amount of welding.-- The rolls are placed as pre-determined in the blueprint or design.-- If the lining is going over a slope it is laid vertically up and down the slope. Additionally, material that is deployed on a slope should be carefully unrolled and not simply unrolled freely downhill. On slopes that are curved, material may require a diagonal cut in order to ensure welds are perpendicular.-- The installers will take careful precautions to prevent wrinkling--  Anchor the linings as they are laid. Usually sandbags or tires are used.GEOMEMBRANE WELDINGGeomembrane lining systems require welding that should performed by qualified technicians.There are two primary welds that are commonly utilized in geomembrane installation:Double hot wedge weldingExtrusion welding. Double hot wedge welding is the preferred method and the most reliable.-- The surface area that will be welded should be free of debris or any foreign materials.-- If extrusion welding is used, oxidation must be removed by grinding and debris from grinding must be removed.-- Double welds are used frequently in order to create a channel of air between welds that facilitates testing.-- Trial welds are made on a regular basis. Packaging & ShippingHDPE Geomembrane Packing and Delivery1. The products are usually tied with packing tape.The packaging size and container capacity of the product are different from the product specifications2. Container transportation, according to your project request. 3. Port: Qingdao, China.Company ProfileTai'an City RuiHeng Building Materials Co., Ltd is specialized in the research, development, production and sales of geosynthetic materials, plastic products and plastic machinery. Our company is devoted to geosynthetic material research and development and application.Our main products are hdpe geomembrane liner,plastic geogrid, geotextile,3D geomat,geocell,geomembrane welding machine,extrusion welder and welding rod,etc. Our products have been widely used by clients in more than 20 countries a