2024 Rcc-03 Remote Control for Xth 8000-48 Inverter/Charger

Application of RCC-03 Setting on The Xtender,fangpusun PSM / PSHVario Tracks,Vario Strings  → → → → → Click to get more details information → → → → →  About settings of RCC-03  1. ESC is Start button of RCC-032. Set the charge and discharge parameters (battery type, maximum charging current, three-stage charging voltage, over discharge protection, maximum AC input current, battery priority or mains power priority, etc.) according to the battery type. Since the requirements of each system are different, set the specific parameters. If you are unsure during the setting process, please contact me.3. After modifying the inverter parameters, please record and save them (which can be recorded in the "user modified value" column of the parameter setting table on pages 52-58 of the inverter manual) for future reference.→ → → → → Click to get more details information → → → → →  Common setting parameters1. Mains power priority / battery priority selection 1296 is the setting item of battery priority or mains power priority. If this item is set to "no", mains power priority is set to "yes", battery priority is set, and the default value is "no". When 1296 is set to "yes", the value of 1297 needs to be set according to actual needs. When the battery voltage is higher than this setting value after a charging cycle, The battery will give priority to energy output.2. Battery undervoltage protection  1108 is set as the battery voltage low-voltage protection point under no-load condition. 1109 is set as the battery undervoltage protection point under full load condition. 1190 under voltage protection delay time under full load (when the battery voltage is lower than 1109 and the duration is greater than 1190, the inverter stops output)3. After undervoltage protection, the inverter recovers the output voltage value.1110 is the battery voltage point at which the inverter recovers the output after battery undervoltage protection (After the battery undervoltage protection of the inverter, when the battery voltage is higher than the 1110 setting value again, the inverter outputs again)4. Battery charging voltage setting (prevent overcharge)1156 and 1140 are the setting values of the three-stage charging voltage point. Since the lithium battery does not need three-stage charging, we can set the values of 1156 and 1140 to the same (The set value is less than -0.5v of the maximum charging voltage of the lithium battery pack to prevent overcharge of single cells caused by unbalanced single cells).5. Maximum charging current1138 is to set the maximum charging current value of each inverter, and it is recommended to set it to 30-40A (to prevent damage to new battery caused by excessive charging current)6. Remote input command setting1545 is to set the remote command input as open point valid or closed point valid. 1576 is set to "yes". When the remote command input is valid, start or turn off the inverter. The above is some basic parameter settings of the inverter. For more function settings, please contact us at any time!→ → → → → Click to get more details information → → → → →  Benefits of Buy Inverter1. It's not just the inverter, it also can charge the battery from generator, solar panel, grid power2. high efficiency 95%, it takes less time to fill the battery than other charger3. Warranty 5 years4. As same as Europe design and with competitive price5. Compatible Switzerland Studer products6. No magnetic interference, especially suitable for hospital precision instruments, banks, supermarkets, school and other large places  → → → → → Click to get more details information → → → → →  Installation Instructions → → → → → Click to get more details information → → → → →        → → → → → Click to get more details information → → → → →   → → → → → Click to get more details information → → → → →   Detailed Photos   → → → → → Click to get more details information → → → → →   Related products   YTM energy storage system          VT-80 MPPT solar controller                     wifi module        → → → → → Click to get more details information → → → → →    → → → → → Click to get more details information → → → → →  Packaging & Shipping       /* January 22, 2024 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(",").forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1