Introduction of Traction TransformerCPEPE's liquid-filled
substation transformers are designed, built, and tested in
accordance with international standards including IEC 60076,
GB1094, ANSI C.57, CSA, NEMA and IEEE. The insulating liquid can be
mineral oil, high flash point ester fluid and silicon oil. The
product is suitable for electrified railway traction power supply
system. Usually the transformer core is laminated type, and our
wound type core is also possible if required by customer, Wound
core traction transformer is a kind of energy-saving transformer
with many outstanding advantages: Low no-load loss, low no-load
current, low noise, strong anti-short circuit ability and overload
capacity, the transformer is energy efficient and environmentally
friendly.Product RangeVoltage level: 110 kV, 220kV Voltage
regulation: ±2×2.5%, ±3×2.5%, ±4×2.5% Capacity: 8000kVA~75000 kVA
Technical characteristics Low no-load loss, low no-load current,
low noise The Laminated core type
transformer Adopt multistage step lapped joint fully-oblique
structure, can reducing magnetic resistance and noise; Its cross
section is inscribed polygon, high fill factor. After high
temperature annealing of eliminating stress, no-load loss is
greatly reduced.Strong overload capacity
With oil flow guide control technology, the quantitative
calculation of the oil flow, optimize the structure of oil circuit,
reduce the hot-spot coefficient, to ensure that under the condition
of rigorous overloading load, the winding hot-spot temperature does
not exceed 140 ºC.Strong anti-short circuit ability
By analyzing and calculating the worst short
circuit, adopting high strength wire and effective support to
strengthen the structure, adjusting the coil distribution to ensure
all stress have enough margin. Self-developed winding technology
can make the coils wind tightly.Low partial discharge
Strictly control each part of the electric
field intensity, according to the discharge requirements, coil
winding and internal assembly is in the dustproof workshop to
guarantee the body clean, adopts the high vacuum oil injection
process, effectively control discharge of product. Important
FeaturesThe core is kind of a wound core. The whole core is
composed by three identical single frames. Each single frame is
wound by several ladder shaped material strips continuously and
orderly.The lengths of three magnetic circuits are the same and the
shortest. So no-load current of three core limb is small and three
phases are balanced. Saving 15% of silicon steel than flat wound
core.The core is wound tightly without seams. It has the advantages
of lower no-load current, smaller magnetic resistance and lower
loss. It also reduces the noise level.The core is wound tightly
without seams. The cross section of wound core is similar to a
circle. The core frame is wound by machine. Filling factor can
reach 0.95~0.97Rectangular material strap will be cut along the
line in the picture and then will be wound. No waste, material
utilization by 100%Reduce 25% no-load loss and no-load current of
more than 70%Reduce noise level 7~10dBBalanced magnetic circuit of
three phasesGood stability, the better anti-short circuit
abilityGood anti-short circuit abilityLow partial dischargeGood
overload capacityTechnical Specification220kV traction
transformerRated Capacity (KVA)Voltage Combination (kV)Connection
SymbolNo-load Loss(kW)Load Loss (kW)No-load Current
(%)Short-circuit Impedance (%)HV (kV)LV
(kV)12500220±2×2.5%27.5Ii012730.610.5~12.51600015750.52000017770.52500020910.531500231090.440000271300.450000321540.463000381830.3110kV
traction transformerRated Capacity (KVA)Voltage
Combination(kV)Connection SymbolNo-load Loss (kW)Load Loss
(kW)No-Load Current (%)Impedance Voltage (%)HV (kV)LV
(kV)6300110±2*2.5% 110±3*2.5% 110±4*2.5%2*27.5Ii0i0 Ii0i67.8
32 0.63% 8.4%
10.5%80009.3380.63%1000010.6450.56%1250012.5550.53%1600014.6650.47%2000016.9750.45%2500020.1880.42%3150023.61040.38%40000 28.3
125 0.35%50000 34.0 148 0.34%63000 41.0 173
0.28%75000 47.0 190 0.27%Changzhou Pacific Electric
Power Equipment (Group) Co., Ltd is a high-tech enterprise in
research, design, manufacture, market and service in High Voltage
and Low Voltage power transmission and distribution
industry.Established in 1989 and organized as a comprehensive power
solution group company in 1997. The company has a registered
capital over USD 20 million and fixed assets over USD 100 million.
The company is located in the center manufacturing zone of China,
near to Shanghai city, occupies a total area of 240,000 square
meters. The annual production capacity is over 20,000 sets of high
and low voltage switchgears and 3,000MVA different kinds of
transformers. The products are widely used in the area of
high-speed railways, subway, city tram, petrochemical, metallurgy,
power substation, power plants, high-rise buildings etc. With
the strong manufacturing backgrounds over the decades, Changzhou
Related products about Low Noise Auto Transformer Genious Factory Power Grid
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup