Arm1l Series Residual Current Protected Circuit Breaker Arm1l-125A-4300 MCCB 4poles 125AMP Molded Case Circuit Breaker

Product DescriptionProduct OverviewResidual current circuit breaker, mainly applicable to AC 50Hz, rated voltage 400V, rated current up to 800A in the distribution network, used to provide indirect contact protection to people, can also be used to prevent fire hazards caused by equipment insulation damage, resulting in ground fault current, and can be used to distribute electrical energy and protect the line and power supply equipment overload and short circuit, but also as the line of infrequent conversion and motor Infrequent switching and motor starting. Conventional leakage protection module with residual current protection circuit breaker work power sampling for two-phase, this series of circuit breakers for three-phase, if the lack of a phase, circuit breaker leakage protection module can still work normally; rated residual action current and maximum disconnection time according to the actual situation on site adjustable; when the phase voltage is reduced to 50V, leakage protection module can still work normally Envirinment of use1,The surrounding air temperature state is: -5ºC~+40ºC2,The altitude of the installation site does not exceed 2000m3,The relative humidity of the air at the installation site does not exceed 50% at the highest temperature of +40ºC, and can have a higher relative humidity at lower temperatures, such as up to 90% at 20ºC. Special measures should be taken for the occasional condensation due to temperature changes.4,The pollution level is 35, wet and hot band type (TH type) circuit breakers through GB/T2423.4, GB/T2423.18 test requirements, can withstand the effects of humid air, salt spray, oil mist, mold.6,The circuit breaker should be installed in a place where there is no danger of explosion and no conductive dust, not enough to corrode the metal and destroy the insulation7, the circuit breaker should be installed in a place where there is no rain or snow intrusion8,Operating conditions: the circuit breaker passes the test requirements of GB/T 2423.1 and GB/T2423.2, the surrounding air temperature can be as low as -25ºC (ARM1DC/ARM3DC/ARM6DC can provide temperature as low as -40ºC, consult our company), as high as +70ºC (more than 40ºC reduced capacity use, see the technical information in the attached sample)Product ParametersBasic Info.ModelCurrent shell frameRatedcurrent(In)Use CategoryPolesUeIcuIcsI△nI△noI△mUiUimpMechanical EnduranceElectricalsafelifeFlashover distance(mm)ARM1L-125M125A16A,20A,25A,32A,40A,50A,63A,80A,100A,125A,Class A3P400V50KA35KA1:100,300,5002:30,100,300 I△n x50%Icu x25%1000V8KV85001500≯50ARM1L-125M125A16A,20A,25A,32A,40A,50A,63A,80A,100A,125A,Class A4P400V50KA35KA1:100,300,5002:30,100,300 I△n x50%Icu x25%1000V8KV85001500≯50ARM1L-125H125A16A,20A,25A,32A,40A,50A,63A,80A,100A,125A,Class A3P400V85KA50KA1:100,300,5002:30,100,300 I△n x50%Icu x25%1000V8KV85001500≯50ARM1L-125H125A16A,20A,25A,32A,40A,50A,63A,80A,100A,125A,Class A4P400V85KA50KA1:100,300,5002:30,100,300 I△n x50%Icu x25%1000V8KV85001500≯50 ModelRated current (In)PolesStructure sizeDimension(W*L*H1)Dimensions(W*L*H2)ARM1L-125M16A,20A,25A,32A,40A,50A,63A,80A,100A,125A3P92*150*11092*150*92ARM1L-125M16A,20A,25A,32A,40A,50A,63A,80A,100A,125A4P122*150*110122*150*92ARM1L-125H16A,20A,25A,32A,40A,50A,63A,80A,100A,125A3P92*150*11092*150*92ARM1L-125H16A,20A,25A,32A,40A,50A,63A,80A,100A,125A4P122*150*110122*150*92Detailed PhotosFAQ1.Q: Are you trading company or manufacturer ?   A: We are manufacturer and specializing in manufacturing good quality of MCCB.2.Q: How long is your delivery time?   A: Normally 5-10 days if there are goods in stock. Or it will take 15-20 days. For customized   items, the delivery time depends.3.Q: What is your terms of payment ?   A: 30% T/T in advance ,and the balance before shipment. 4.Q : Can you make customized products or packing?   A: Yes.We can offer customized products and packing ways can be made according to customer's requirement.5.Q: Can you offer mould making services?A: We have made many mould for different customers for years.Wecan offer DMC Thermosetting Compressionmoulding,Thermoplastic injection moulding,Metal stamping moulding.6.Q: How about the guarantee period?A: It varies according the different kinds of product. We can negotiate it before place an order.7.Q: What is your production capacity?   A: We can produce 3000  sets per month.8.Q: How about the scale of your factory?   A: Our total area is 7000 square meter. We have 300staffs, .40 engineers.9.Q: What tests do you have to confirm the quality of the arc chamber?   A: We have a incoming inspection for the raw material and process inspection for the rivet and stamping. There is also final statistical audit which consisting the measurement of sizes, tensile test and coat examine.10.Q: What are the countries you have exported to?A: We have not worked directly with foreign customers before, we provide ODM and OEM services for brands in China and then they take our products and sell them to foreign customers, b