1. Product SummaryWR1002JLED is a new modular two-output CATV
network optical receiver. It adopts modular design, use more
flexible. Microprocessor control, digital display the parameters,
the engineering debug is especially easy. It is the main equipment
to build the CATV network. 2. Performance CharacteristicsHigh
response PIN photoelectric conversion tube.Optimized circuit
design, SMT process production, optimized signal path, make the
photoelectric signal transmission more smooth.Specialized RF
attenuation chip, with good RF attenuation and equilibrium linear,
high accuracy.GaAs amplifier device, power doubler output, with
high gain and low distortion.Single Chip Microcomputer (SCM)
control equipment working, LCD display the parameters,
convenience and intuitive operation, and stable
performance.Excellent AGC performance, when the input optical power
range is -9~+2dBm, the output level keep unchanged, CTB and CSO
basically unchanged.Reserved data communication interface, can
connect with the Ethernet transponder, access to network management
system.Return emission can select burst mode to sharply decrease
the noise convergence and reduce the forepart receiver number.ONU
module optional. 3. Technique Parameter3.1 Link testing
conditionsThe technique parameters of this manual according to the
measuring method of GY/T 194-2003 , and tested in the following
conditions. Testing conditions: Forward optical receive part: with
10km standard optical fiber, passive optical attenuator and
standard optical transmitter composed the testing link. Set 59
PAL-D analog TV channel signal at range of
45/87MHz~550MHz under the specified link loss. Transmit
digital modulated signal at the range of 550MHz~862/1003MHz, the
digital modulated signal level (in 8 MHz bandwidth) is
10dB lower than analog signal carrier level. When the input
optical power of optical receiver is -1dBm, the RF output level is
108dBμV, with 8dB output tilt, measure the C/CTB,
C/CSO and C/N.Backward optical transmit part: Link flatness
and NPR dynamic range are the link indexes which is composed
of backward optical transmitter and backward optical
receiver.Note: When the rated output level is the system full
configuration and the receiving optical power is -1dBm, equipment
meets the maximum output level of link index. When the system
configuration reduce (that is, actual transmission channels
reduce), the output level of equipment will be increased. Friendly
Notice: Suggest you setting the RF signal to
6~9dB tilt output in the practical engineering
application to improve the nonlinear index (behind the node) of the
cable system. 3.2 Technique ParametersItemUnitTechnical
ParametersOptical ParametersReceiving Optical PowerdBm-9 ~
+2Optical Return LossdB>45Optical Receiving Wavelengthnm1100 ~
1600Optical Connector Type FC/APC, SC/APC or specified by
the userFiber Type Single ModeLink PerformanceC/NdB≥
51 (-1dBm input)C/CTBdB≥ 65Output Level
108dBμVEQ 8dBC/CSOdB≥ 60RF ParametersFrequency RangeMHz45
~862/1003Flatness in BanddB±0.75Rated Output LeveldBμV≥ 108Max
Output LeveldBμV≥ 114Output Return LossdB(45
~550MHz)≥16/(550~1003MHz)≥14Output ImpedanceΩ7575Electronic Control
EQ RangedB0~150~15Electronic Control ATT RangedBμV0~150~15Return
Optical Emission PartOptical ParametersOptical Transmit
Wavelengthnm1310±10, 1550±10 or specified by the userOutput Optical
PowermW0.5, 1, 2Optical Connector Type FC/APC, SC/APC or
specified by the userRF ParametersFrequency RangeMHz5 ~ 65 (or
specified by the user)Flatness in BanddB±1Input LeveldBμV72 ~
85Output ImpedanceΩ75NPR Dynamic RangedB≥15 (NPR≥30 dB)Use DFB
laser≥10(NPR≥30 dB)Use FP laserGeneral PerformanceSupply VoltageVA:
AC (150~265)V; B: AC (35~90)VOperating
TemperatureºC-40~60Storage TemperatureºC-40~65Relative Humidity%Max
95% no condensationConsumptionVA≤
30Dimensionmm290(L)*265(W)*75(H)Note: The forward RF parameters are
tested under the condition of using GaAs 25dB power doubler module
in the last stage. Use other module, the parameters will be
slightly different. Burst Mode (Select this mode, see
below)Optical Output Power(Close the burst mode)dBm -30Laser
Turn On ThresholddBμV≥70Laser Turn Off ThresholddBμV≤62Laser Turn
On Time (t1)us0.5≤ t1 ≤1Laser Turn Off Time (t2)us0.5≤ t2
≤1.5ProcessCompany ProfileContact us /* January 22, 2024
19:08:37 */!function(){function s(e,r){var
a,o={};try{e&&e.split(",").forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
Related products about CATV Fttc FTTB Rfog Outdoor Optical Receiver Node Wr1002jled
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup