3000 Rpm Brushless Servo System (motor + drive)

3000 RPM Brushless Servo System(motor + drive)57IV90/57IV130/57IV180 Features1.Operating voltage: DC input voltage 15VDC to 50VDC ,recommend voltage is 36V2.The max continuous output current is 10A, the max peak current is 22A (3 times overload capacity) 3.Acceptable differential or single-ended pulse / direction command, have three control mode of position, speed and torqe4.Using FOC magnetic position control technology and space vector pulse width modulation (SVPWM) closed-loop control technology5.The number of pulses per cycle (subdivision) can be set by the debug software or the dial switch setting(electronic gear ratio)6.Have three types of 90w,130w and 180w DC brushless servo motor to choose.7.Have protection of overvoltage, undervoltage, overcurrent and tolerance,etc.8.Single / double pulse mode, the pulse valid edge can be choose.9.The max pulse frequency of control instruction is 500KHz (factory default is 200KHz)10.Pulse, direction and enable signal input interface level is 4.5 to 28V compatible11.With serial RS232 / RS485 debugging function, but need to use our special serial debugging cable 12.Performance: smooth speed, small overshoot ,small tracking error, low heat of motor and driverAdvantageThis servo motor system is made up of brushless servo motor with driver built-in.Compact and small size is suitable for some place that has requirement of volume.It has less wiring to reduce errors,keep stable and easy for installation.This integrated servo system has good speed adjustment performance,large starting torque,smooth operation, high rotating speed.The price is much lower than AC servo motor, but some performances are better than AC servo products.Driver Model And Selection GuideMotor Type 57IV9057IV13057IV180Rated power(W)90W130W180WVector Maximum Current16A18A22ABody Length(MM)106.2 0.5126.2 0.5146.2 0.5Operation Voltage15-50Vdc,36Vdc recommend Overvoltage Protection Voltage68Vdc±2Control Method32 bits DSP vector FOC control technologyPulse Limit Frequency500KHz(factory default 200KHz)ProtectionOvercurrent, overvoltage, undervoltage and tracking error tolerance alarmInput Signal Pulse, direction and enable differential / single-ended interface signal,interface level 4.5-28Vdc compatible, no need external current limiting resistorOutput Signal Alarm / in-position signal OC output, the output capacity is100mA, need externalpull-up resistor, the maximum pull up voltage is 24VdcElectronic Gear RatioDefault 4000 / rev, through the DIP switch or debug software setting subdivision(200-51200)Position Error Control Accuracy±1 PulseSpeed Control Accuracy ±2 rpmMaximum  Acceleration100 rpm/msDialing Switch SettingsPulse/Rev.SW1SW2SW3SW4DefaultONONONON800OFFONONON1600ONOFFONON3200OFFOFFONON6400ONONOFFON12800OFFONOFFON25600ONOFFOFFON51200OFFOFFOFFON1000ONONONOFF2000OFFONONOFF4000ONOFFONOFF5000OFFOFFONOFF8000ONONOFFOFF10000OFFONOFFOFF20000ONOFFOFFOFF40000OFFOFFOFFOFFSubdivision accuracy (electronic gear ratio) :When SW1, SW2, SW3, SW4 are ON, the drive uses the internal default micro-step subdivision, the default internal subdivision of the driver is 400Pulse / rev, and the electronic gear ratio can also be set by the debugging software. SW5 set the motor direction,when turnON, the motor turns clockwise (CW),when turn OFF, the motor turns counterclockwise(CCW). SW6 control mode selection, whenON, the motor enters the self-test mode,making one forward and reverse revolution, has been repeated until exit self-test mode, the external control signal is invalid at self test mode, whenOFF, the motor exits self-test mode,then the external control signal is valid.Mechanical Structure Dimension Driver modeMotor body length(mm)Driver thickness(mm)Integrated motor driver length(mm)57IV907630.2106.257IV130 9630.2126.257IV180 11630.2149.2Note : All above is normally used, and we can customize according to your request or choose the suitable model for you, please tell us following parameters: current, voltage, holding torque, body length,the application area.ApplicationSuitable for all kinds of small and medium-sized automation equipments and instruments. Such as: laser equipment, medical equipment, 3D printer, small and medium-sized engraving machine, electronic processing equipment, automatic crawling equipment, special CNC machine tool, packaging equipment and robot. It is especially useful for users who expect low noise and high speed applications.Packaging and shipping1.Outer packing: Standard export carton with required shipping marks2.Inner packing: Waterproof packing with shock absorbing EPE and cardboard surrounded 3.As per the clients requirementsOur service1.Working time : 8:00 a.m - 10:00 p.m .Any questions, please tell us freely, we will be reply you asap.2.Lead time : For samples, 2 to 5 days will be OK. For mass production, the lead time depend on the quantities you need.3.Warrantity period : 18 months and Life-long maintenance service for the product.4.We accept products customize.FAQQ1: How to choose t