Gma-TCP Series Posital Baumer P+F Equivalent Replacement Modbus TCP Ethernet Multi-Turn Absolute Encoder

EtherNET Multi-turn Absolute Encoder With Modbus-TCP Interface  Product DescriptionGMA-TCP SeriesHousing Diameter: 58mm;Solid Shaft:10mm;Interface: Modbus TCP;Number of the absolute ascertainable revolutions: 8192ppr(13Bits)         Total number of turns:4096(12bits)Supply Voltage:8-29v; Output Code: Binary;Widely used in various fields of automatic control and measurement system,such as machinery manufacturing, shipping, textile, printing, aviation, industry Testing machine, elevator, etc.Vibration-resistant, corrosion-resistant, pollution-resistant;Product ParametersProduct characteristicsHousing Dia.:60mmShaft Dia.:Solid shaft 10mm/Blind hollow shaft 12/ 15mmElectrical DataResolution:Number of the a bsolute ascertai nable revolutions: Si ngle t urn 65536 ppr(16BITS)Turns: 12bitsInterface:Modbus-TCPOutput Code:Binary, Gray, Gray Excess, BCDSupply Voltage:24v ,8-29VMax  Frequency Response33Khz~4MhzStart Torque9.8×10-4 N*MMax. Shaft LoadingAxial: 30N, Radial:20N;Max. Rotary Speed3000rpmWeight300gEnvironment DataWorking Temp.-30~80CStorage Temp.-40~80CProtection GradeIP65Connection Leading:Signal8-30vGNDTxd+Txd-Rxd+Rxd-PinPOWER-1POWER-3IN-1IN-3IN-2IN-4ConnectorM12-A/ 4 PinsMale -1M12-A/4 PinsMale -3M12-D/4 PinsFemale -1M12-D 4 PinsFemale -3M12-D 4 PinsFemale -2M12-D 4 PinsFemale -4 M12-A Male ConnectorM12-D female ConnectorInstructionsEncoder default IP: 192.168.0.200Default netmask: 255.255.255.0Default Gateway: 192. 168.0. 1Port number: 502Register AddressDefinitionDescription0x00Encoder output position High 16 bits 0x01Encoder output position Low 16 bits 0x02Current position laps 0x03The number of single laps at the current position 0x41Counting direction0 increases clockwise, 1 increases counterclockwise0x45Set the high 16 bits of the current position 0x46Set the lower 16 bits of the current position 0x47IP_ADDRESS[0]Local IP0x48IP_ADDRESS[1]Local IP0x49IP_ADDRESS[2]Local IP0x4AIP_ADDRESS[3]Local IP0x4BNETMASK_ADDRESS[0]Netmask0x4CNETMASK_ADDRESS[ 1]Netmask0x4DNETMASK_ADDRESS[2]Netmask0x4ENETMASK_ADDRESS[3]Netmask0x4FGATEWAY_ADDRESS[0]Gateway0x50GATEWAY_ADDRESS[ 1]Gateway0x51GATEWAY_ADDRESS[2]Gateway0x52GATEWAY_ADDRESS[3]GatewayDimensionsNote: Adopt elastic soft connection shall be applied between encoder shaft and output shaft of user end to avoid damage of encoder shaft system due to serial movement and run out of user shaft. Please pay attention to the allowable axle load during installation. Make Sure that the difference Between Axial Degree of encoder shaft and user output shaft shall be no more than 0.20mm, and the deviation angle with axis shall be less than 1.5 ° . Try to avoid knocking and falling collision during installation; Do not connect the power line and the ground wire in reverse. The GND wire shall be as thick as possible, generally larger than φ 3. Output lines of encoder shall not be overlapped with each other to avoid damaging output circuit. Signal line of encoder shall not be connected to DC power supply or AC current to avoid damaging output circuit. The motor and other equipment connected to the encoder shall be well grounded without static electricity. Shielded cable shall be used for wiring. Before starting the machine, carefully check whether the wiring is correct. During long-distance transmission, the signal attenuation factor shall be considered, and the output mode with low output impedance and strong anti-interference ability shall be selected. Avoid using in strong electromagnetic wave environment. Certifications Company Profile GERTECH is an technical enterprise Located in Weihai City ShanDong Province, China, has been providing Professional Industrial Automation Sensors Solutions for hundreds of enterprises all over the world since 2004. We offer the world's broadest range of encoders for motion feedback control. For 17 years, Gertech have been providing innovative, customized system solutions for virtually any heavy-duty, industrial, servo- or light-duty application,and is committed to our people, customers and community and strives for excellence in safety, quality, delivery and customer service.Gertech Manufactures and supplies safety systems for the door and gate market. The product portfolio includes optical and pneumatic sensing edges, bumpers, and photo-eye sensors which meet international standards for safety devices. These products have applications in commercial, bus, and train doors as well as production machines.Our Main Products: A. Incremental Encoder; B. Programmable Incremental Encoder; C. Single-turn and multi-turn Absolute Encoder with Parallel, SSI, Modbus, Profibus, Canopen, Profinet, DeviceNet and EtherCaAT interfaceS; D. Draw Wire Encoder; E. Manual Pulse Generator; F. Optical Encoder Kit; G. Servo motor encoder;Certificates: CE,ROHS,ISO9001,ETC.Gertech Sensors are widely applied in the textile machinery, hoisting cranes, CNC machine, experimental machine, satellite communication, electric cars, water conservancy project, nuclear power equipment,