High Voltage Disconnector Switch Isolaing Switch132kv

Center Break Isolator and double Break Isolator  These disconnectors are , no load switching devices which physically isolate the lines. They are designed for horizontal outdoor application and can also be designed for vertical installation. For earthing and closing of switchyard portions of the installation, the earthing switches are provided on disconnector. If required. The following documents were referred to during the preparation of this specification. In case of conflict, the provisions of this specification shall take precedence. IEC 129:1975: Alternating Current Disconnectors (Isolators) and Earthing Switches IEC 60694:2002: Common Specifications for High Voltage Switchgear and Controlgear BS 729: Hot dip galvanized coating on iron and steel articles IEC62271-102 Isolator (Disconnector) - a mechanical switching device which provides, in the open position, an isolating distance in accordance with Electrical Safety requirements. SERVICE CONDITIONS The isolator shall be suitable for continuous operation outdoors in tropical areas at altitudes of up to 2200m above sea level, humidities of up to 90%, average ambient temperature of +30ºC with a minimum of -1ºC and a maximum of +40ºC and heavy saline conditions along the coast. 4.2. DESIGN AND CONSTRUCTION 4.2.1 The Isolator, Solid Link shall be designed and constructed in accordance with IEC 129 and IEC 60694. 4.2.2 The isolating link shall be of the vertical opening, designed for single phase manual operation. It shall be easily removed and replaced by using a portable operating rod. 4.2.3 The isolating link shall incorporate double porcelain insulators to suit voltage requirements and mounted on hot dipped galvanised steel under base suitable for vertical mounting. 4.2.4 The isolating link shall be arranged so that each unit is mounted independently on an angle bracket. It shall be supplied complete with the angle bracket and accessories suitable for mounting on 'U' type steel channel. The drawings to be submitted shall indicate all the applicable mounting positions. 4.2.5 The isolator shall be designed such that in fully open position, it shall provide adequate electrical isolation between the contacts on each phase. It shall conform to the requirement as single point isolation for safety. 4.2.6 All steel parts shall be hot dip galvanized to BS 729. The minimum coating of galvanizing required is 80 microns. 4.2.7 The solid link shall be removable from the mounting by use of operating rod. 4.2.8 All current carrying parts of the isolator shall be made of high conductivity material. 4.2.9 The isolator shall be fitted with clamp connectors for Aluminium (ACSR) conductor of Aluminium (ACSR)conductor of up to 18.2mm diameter. The rating of the complete isolator shall be as follows: - Rated voltage 36 kV Rated frequency 50 Hz Rated lightning impulse withstand voltage 200 kV Rated power frequency withstand voltage, dry 95 kV Rated normal current 400 Amps Rated short time withstand current for 3 sec, min. 18.0 kA Minimum creepage distance of insulators 900 mm     SOLID LINKS 11KV          N/ODETAIL DATA1Description Solid link assembly complete with linkrated at 200A and mounting bracket to PIESA 002. (See Figure 1  to Figure 12 below)2System conditions of service   a) nominal Voltage (Un) r.m.s    kV    11b) maximum system voltage (Um) r.m.sKV12c) earthing Effective & non effectived) FrequencyHz503Site conditions of servicea) altitude m 1400b) Operating Ambient temperature°C-1 to 40c) Humidity%854Rating  a) Nominal voltagekV11b) Rated currentSolid link A 200 Cut out base A 2005Electrical components  a) Insulator material specification PorcelainDielectric strength  Lightning  impulse withstand (1.2/50)kV95Power frequency wet withstand voltager.m.skV286Specific creepage distancemm/kV25      7General information to be providedwith bid:Drawings and brochures showing outline and general arrangement    Yes/No    Yes b) Detailed drawings of all itemsshowing critical tolerances to be provided with bidYes/NoYes8Previous Type test report/certificate oncomplete solid link assembly to be provided with bid Yes/No Yes10Routine tests (acceptance tests onsampleProduct) to be provided on deliveryYes/NoYes11Applicable standard PIESA 00212Other applicable standards NRS 035SABS IEC 60282-2SABS IEC 60186BS 137 part 2      TRI-LINKS      Lot 3-(a) 11kV with interrupters      N/ODETAIL DATA1TYPE 11kV pre-assembled gangoperated overhead line load break switch complete with expulsion interrupters2Mounting configuration Horizontal3Mode of operation Manually operated polemounted linking rod and handle with locking facilities a) nominal Voltage (Un) r.m.skV11b) maximum voltage (Um) r.m.sKV12c) earthing Effective & non effectived) FrequencyHz50e) rated currentAmp400f) Fault closing capacitykA12.54Site conditions of servicea) altitude metres 1400b) Operating Ambient temperature °C -1 to +40c) Relative humidity%855Electrical components  a) Insulator material specification High Temp