Rads Series Hall-Effect Rotary Angle Displacement Sensor with External Actuator

RADS series Hall-effect Rotary Angle Displacement Sensor with External ActuatorRADS Series Hall-effect Rotary Angle displace Sensors provide non-contact sensing in harsh transportation and industrial applications at a competitive cost.RADS Series: Takes non-contact sensing to the next level by separating the magnet from the sensor body. The absence of the actuator shaft removes the wear and tear on the bearings caused by radial forces.  A choice of a bare or a housed magnet is available.These products use a magnetically biased, Hall-effect integrated circuit (IC) to sense rotary movement of the actuator over a set operating range. Rotation of the actuator changes the magnet's position relative to the IC. The resulting flux density change is converted to a linear output.The IC, together with conditioning and protection circuitry, is sealed in an IP69K-qualified rugged package for durability in most harsh environments.Multi operating ranges from 60° to 360° are tolerant to over-travel and allow use in most common applications. Low voltage and high voltage versions cover an input voltage range of 4.5 Vdc to 30 Vdc.  FeaturesTrue, non-contact operationunlimited rotation (RAS Series)Solid-state Hall-effect technologyRugged IP69K-sealed package with integral connectorAutomotive-grade EMI/EMC testing, integrated reverse polarity, and short circuit protectionIndustry-standard AMP termination, 32 mm mounting pitch, North American or European pin-out styles, and compact packageMulti operating ranges up to 360°Potential ApplicationsTRANSPORTATIONPosition and movement detection (pedals, throttles, gear shift, levers, steering, linkages, and hitches) in trucks, buses, off-road vehicles, cranes, and industrial/ construction/agricultural vehicles and equipment)Suspension/kneeling position (buses, trucks)Tilt/trim position (boat engines, tilling equipment)INDUSTRIALValve controlHVAC damper controlIrrigation equipment pivot controlHall-effect Rotary Angle Displace SensorsElectrical SpecificationsCharacteristicRADS  series (Low Voltage)Supply voltage5 ±0.5 VdcSupply current:   Normal20 mA max.During output to ground short25 mA max.Output:      standard0.5 Vdc to 4.5 Vdc   Ratio-metricinverted4.5 Vdc to 0.5 Vdc   Ratio-metricOutput signal delay4 ms typ.Reverse polarity protection-10 VdcOvervoltage protection10 VdcOutput to ground short circuitcontinuousResolution12 bitOutput load resistance  (pull down to ground)10 kOhm typ.EMI:  radiated immunity100 V/m per ISO11452-2 from 200 MHz to 1000 MHzEMI:   conducted immunity100 mA BCI per ISO11452-4,  from 1 MHz to 200 MHz  able 2. Mechanical SpecificationsCharacteristicRADS Series  (Low Voltage)Expected lifeinfinite rotationAir gap: bare magnet actuator3,00 mm ±0.5 mm [0.12 in ±0.02 in]Air gap: housed magnet actuator2,00 mm ±0.5 mm [0.08 in ±0.02 in]misalignment2.002,00 mm [0.08 in] max.Material: magnetNdFeBsensor housingPBT plastichoused magnet over-mold  sensor/PPS plastichoused magnet bushing sensor bushingbrassMating connectorAMP Super-seal 282087-1Mechanical end stopnomounting screw sizes:sensor to mounting surfacenon-magnetic, stainless steel M4 X 0.7 screws and8 mm [0.31 in] OD washershoused magnet actuator toactuator mounting shaftnon-magnetic, stainless steel M3 X 0.5plain cup point set screwsApprovalsCETable 3. Environmental SpecificationsCharacteristicRADS Series (Low Voltage)Operating temperature range-40 °C to 125 °C [-40 °F to 257 °F]Ingress protectionIP69KMedia compatibilityheavy transportation fluidsShock150 G peakVibration120 G peakSalt fogbare magnet: 96 hr for as per ASTM B117housed magnet: 240 hr per ASTM B117NOTICEFerrous material or magnet material more than 300 Gauss within 10 mm [0.39 in] from sensor boundary may impact  sensor performance.Available ConfigurationsActuator TypeSeriesActuator TypeIntegral shaft without leverSeparate bare magnet    /* January 22, 2024 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(",").forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1