SAC-131-PM Flat Diaphragm Pressure Transmitter, including strain
type and diffusion silicon front type, strain type flat diaphragm
type measuring end with special treatment of strong flush
diaphragm, the hard particles in the measured medium will not
damage the isolated flush diaphragm. Compact structure, corrosion
resistance, anti-vibration, anti-particle impact, wide range of
temperature compensation. Diffusion silicon front type adopts
imported diffusion silicon core system, using tuning and digital
compensation technology, the product performance is reliable and
stable output.Compact structure and easy installation. Advanced
diaphragm/oil-filled isolation technology. High stability and high
reliability. Anti-vibration, anti-radio frequency interference.
316L stainless steel isolation diaphragm structure. High precision,
all stainless steel structure. Micro amplifier, voltage, current,
RS485 signal output. Strong anti-interference, good long-term
stability. Diversified forms and structures, easy to install and
use. Wide range, can measure absolute pressure, gauge pressure and
sealed reference pressure. Anti-vibration, anti-shock.Power
supply:DC 12~24V Output signal: 4-20mA, 1-5V, 0-10V, 0-5V, RS485
Accuracy level: 0.2, 0.25, 0.5 optional Range:-0.1~0~60MPa(The
range cannot be lower than 10KPa) Pressure type: gauge pressure,
absolute pressure, sealed pressure Compensation
temperature:-10ºC~70ºC Working temperature:-20ºC~85ºC Medium
temperature:-20ºC~85ºC Storage temperature:-40ºC~85ºC Overload
pressure:0.035~10MPa(150%FS)10~60MPa(125%FS) Response time: Current
and voltage output type pressure ≤10ms (rise to 90%FS) RS485 output
type pressure ≤ 100ms (rise to 90% FS) Insulation
resistance:20MΩ/250VDC Protection level: IP65 Load
resistance:(U-9V)/0.02A,U:supply voltage Long-term stability: ±0.2%
FS/year Zero output temperature drift: ±0.3%FS/10ºC Full-scale
output temperature drift: ±0.3%FS/10ºCUse and InstallationThe
pressure transmitter should be installed in a place with low
temperature fluctuation as much as possible, and avoid vibration
and shock.Pressure transmitter can be installed directly on the
measurement point. The connection thread: M20*1.5, M16*1.5, G1/2,
G1/4, NPT1/2 and NPT1/4. For special threads or flanges, please
contact your sales representative.The signal should not be run
through conduit or open trunking with other power lines, or near
high power equipment.If the transmitter is required to use a pilot
tube, you should pay attention to the strong corrosive or
superheated media should not be in contact with the transmitter to
prevent slag in the pilot tube to prevent precipitation, the pilot
tube as short as possible. And in the measurement of steam or other
high-temperature media, the working temperature of the transmitter
should not exceed the limit, for steam measurement, the pilot tube
should be filled with water to prevent the transmitter from direct
contact with steam.Pressure transmitter safety instructionsThe
transmitter should be handled and installed with care to avoid
collisions that could affect the performance of the circuit.Do
not touch the isolation diaphragm inside the pressure inlet of the
transmitter with foreign objects.The external threads of the
transmitter must be sealed, otherwise the pressure will be
unstable.If you encounter any problem during the installation and
use of the product, please contact us. When the product is
abnormal, please do not open it for repair without permission, and
contact the manufacturer in time.This product is not allowed to be
used in explosion-proof situations.CautionThe transmitter is used
in media that are non-corrosive to silicon and stainless steel (or
aluminum alloy)The maximum pressure that may occur instantaneously
in the measured system must not exceed the load
pressure rating.The back end of the pressure transmitter must not
come into contact with conductive or corrosive liquids or gases.No
sharp or hard objects should be inserted into the pressure input
hole to prevent damage to the core.Water must not enter the back
lead of the sensor.Please strictly follow the precautions when
using, otherwise you will be responsible for theconsequences.
Measuring range -100KPa~10KPa~40MPa Pressure type Gauge pressure
(default), absolute pressure Output signal 4-20mA (default), 0-5V,
0-10V Power supply 9~24VDC Accuracy class 0.5%FS (default), 0.2%FS
Compensated temperature -10~70ºC Operating temperature -20~80ºC
Zero temperature drift 0.5%FS (MAX) Sensitivity temperature drift
0.5%FS (MAX) Pressure overload ≤1.5 times Mechanical vibration
20G(20-5000HZ) Sampling time 2400 times in 1 second Long term
stability ≤0.2%FS/year Protection class IP65 Media compatible 316L
Stainless Steel Compatible Fluid Media FAQ Recently1. Q: Can I buy
any of your product accessories?A: Yes you can. Most accessories
are able to purchase, but in a few cases of patented designs or
intellectual property cannot besold. More details pl
Related products about Pressure Transmitter Flush Diaphragm Pressure Sensor
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup