shell and tube heat exchanger with stainless material for
pool Advantages: 1 High speed flow at low pressure drop 2
high quality heat transfer Our heat exchanger fully constructed by
stainless steel 316L OR Ti shell and tubesmaking Pool & Spa Heat
Exchanger a very reliable and effective way transfer heat
indirectly between any boiler and pool or spa circuit, besides
other applicationMounting The method of mounting used is totally
responsibility of the installer. The units are designed for both
horizontal and vertical mounting, it is recommended to always
install the unit with a mounting bracket fixed to a wall, or
ceiling or floor to prevent hammer heads or vibrations which could
damage the unit, the use of expansion joints on the boiler circuit
is recommended.nstallation InstructionsImportant: Always install
the pool & Spa heat exchanger in a counter flow pattern, as shown
in the following figure.Pool & spa heat exchangers should be
installed downstream of the filtration and pumping equipment. The
boiler water must be assisted and the usual precautions taken to
prevent air locks. The pool water pump should be controlled by the
thermostat in the pool pipe work before the heat exchanger and set
at the required temperature.Operation instructionsIt is important
that these instructions are followed to prevent any corrosion or
erosion of Stainless / Titanium pool & spa heat exchanger.Operate
the unit under the following design parameters shell/tube side
pressure: 6 bar (87 psi), Temperature: -5ºC (23ºF)-200ºC
(392ºF)Install unit before chlorination device.Start-upValves
should be opened gradually to achieve a steady increase in flow and
pressure into the unitThe cold (heated) fluid should first enter in
to the systemThe hot(heating) fluid, water or steam, should be
gradually brought into the system.Check all connections for
leaking.Shut-Down: shut down hot fluid side first, then the cold
fluid side.(For Stainless heat exchanger only) Always keep PH
within correct levels. The ideal pool PH should be kept between
7-8. It is extremely important to avoid PH to fall below 7.2 or
above 7.8. you must check daily. Modify your pool condition if
necessary.You must ensure that the chlorine levels are in the range
recommended by your pool chemicals supplier and they are aligned to
your specific needed.If you have installed a by-pass fitted to the
heat exchanger circuit, it is important that any valve is corrected
positioned to allow the recommended pool water flow to pass though
the heat exchanger unit.The filter should be checked
regularly,especially sand filters, this type of filtration if
working improperly will allow sand to pass around the pool circuit
causing erosion of the heat exchanger and other components of the
system as well. /* January 22, 2024 19:08:37
*/!function(){function s(e,r){var
a,o={};try{e&&e.split(",").forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
Related products about Titanium Shell and Tube Heat Exchanger for Swimming Pool
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup