Terek Brand Factory Directly Low Price High Quality Safety Valve Calibration Test Bench

PRODUCT DESCRIPTION :   Used for testing all kinds of safety valve, such as spring directly load safety valve, Power assisted safety valve, Supplementary loaded safety valve, fully open, slightly open, flange, thread type safety valve. Safety valve test bench is to use high pressure air or nitrogen as the medium to test the sealing performance of the safety valve, jump pressure, back seat pressure, etc., for a variety of safety valve set pressure adjustment, set pressure test, discharge pressure test, back seat pressure test, test the pressure sealing performance of the safety valve, leakage rate. Safety Relief Valve Test bench has obvious advantages in techniques, test accuracy, safety etc. 1. Automatic hydraulic clamping, Adjustable clamping force, equipped with gauges displaying corresponding clamping forces, The material of the clamping valve fittings is stainless steel. 2.The same valve size, TEREK products can test bigger pressure; The same pressure, TEREK products can test bigger valve size; Provide quicker and more accurate clamping force. Control panel with different gauges for reference . 3. With Our self Products air driven booster pump , build up pressure quickly and Holding pressure constant; With high pressure stainless needle valve, installed in either direction, high pressure resistant, high durability;  4.Normally we use double stage air driven high pressure gas booster pump and High pressure air driven liquid pump for building into the safety valve test bench. We are able to provide our customers better technical support, price and service. 5. Test various relief valves such as full-open, micro-open, metric, flanged and threaded etc. Safety valve test bench is used for various safety valve setting pressure adjustment, the whole set pressure detection, discharge pressure detection, back seat pressure testing, assessment of its pressure safety performance etc.. , Safety Relief Valve Test bench has obvious advantages in techniques, test accuracy, safety etc.PRODUCT DETAILS: Safety valve test bench is used for various safety valve setting pressure adjustment, the whole set pressure detection, discharge pressure detection, back seat pressure testing, assessment of its pressure safety performance etc Main technical data for Manual/ Computer control safety valve test bench The safety valve test bench system is mainly composed of power system, valve clamping system,  testing system, electrical control system. Product nameIntelligent digital display instrument control system safety valve test benchModelTVT-40-DN400-MCDrive air source pressure3-8bar.Outlet pressure Control unitDrive air regulator valvePower sourceTEREK gas booster pumpGas pump pressure ratio60:1Test mediumNormal air/NitrogenPressure testing range0-480bar for optionWhen the driven air pressure is 6.6barGas High pressure outlet pressure is 400bar.Min gas inlet pressure25 barMax gas inlet pressure480 barPower sourceTEREK liquid booster pumpLiquid pump pressure ratio64:1Test mediumWaterPressure testing range0-480 bar for optionWhen the driven air pressure is 6.3barLiquid High pressure outlet pressure is 400bar.Test valve diameterDN20-DN400 (0.8inch-15.7inch)Pressure control accuracyless than 1%F.S;Pressure measurement accuracy0.4 pressure gaugeValves and pipingHigh pressure needle valve and stainless steel pipingPressure range scale0-2.5MPA ,0-10MPA ,0-25MPA ,0-60MPA(Can be customized)Interface typeScrew and flange typeClamping wayHydraulic cylinder clamping forceClamping pumpHydraulic pump LKD-40Clamping force range30TonsControl and testingIntelligent digital display control, can be pre - set clamping pressure and test pressure.Supply voltage50Hz -60Hz ,220VControl console Weight400 KGControl console Size1320*920*1550mmControl console Packing size1440*1000*1690mmClamping table weight700 KGClamping table Size1370*820*830mmClamping table Packing size1500*900*990mmPacking typeStandard export wooden caseProduction time20-25 days.Provide Provide High pressure test connecting pipe, high pressure gas pipe of nitrogen cylinder,operation instruction, operation video, repair kit, seal gasket, screw fitting, Seal ring, joint fitting, PU air pipe,Provide flange connection fittings and threaded connection fittings of corresponding specifications .USB disk(Including equipment pictures, operation instructions and operation video files.)etcPRODUCT PICTURES: System configuration:The safety valve test bench system is mainly composed of power system, valve clamping system,  testing system, electrical control system.1)Power system Air drive gas or nitrogen booster pump, air driving pressure 3-8bar;Maximum Output pressure 480bar; Provide high pressure for valve test.2)Clamping system. The liquid booster pump provides high pressure power. Cylinder clamping ensures the sealing between the tested parts and the pipeline.3)Test system. Pressure range: 0-1MPA; 0-2.5 MPA, 0 -16 MPA, 0-25 MPA and 0-60MPA. The performance index is up to the accuracy of ± 1%FS, and