Compair/Gardner Denver OEM A11830674 Customized Products Air Compressor Part End Shaft Seal Kit

Compair/Gardner Denver  OEM A11830674 Customized Products Air End Shaft Seal KitThe shaft sleeve is a part of the sealing system, the main role is to protect the spindle from wear (replacing the shaft sleeve than changing the shaft saves time and money - if not the shaft sleeve, the mechanical seal of the static pair will directly wear the spindle, lead to spindle damage in the long run).Product NameShaft SealProduct NumberA11830674Design ForCompair/Gardner DenverBrandQINGDAO FUTAIMaterialStrict implementation of air compressor parts technical standardMOQ1 PCDelivery time10-15 daysConditionNew Properties of single lip sealGood sealing performance with pressurized mediaSuitable for dry runs and lubricated applicationsAlso suitable for soft shafts1616562580 PTFE Oil Seals Atlas Copco Screw Compressor Repair Parts oil seal double lip Rotary Seal1616601100 PTFE sealing shaft oil Seal Used For Air Compressor1616601200 air compressor ptfe lips oil seals rotary shaft seal1616601100 PTFE sealing shaft oil Seal Used For Air CompressorGAS ATLAR 1616-5623-00 Stainless steel mechanical seal PTFE rotary oil seals for tamrock1616562500 Ptfe carbon lip seal Stainless steel oil seal for Atlas screw air compressor1614950600 ptfe rotary seal air compressor shaft seal screw compressor oil seal1614942900 PTFE stainless steel rotary shaft oil seal for air compressorOS-G3214 CARLOCK PTFE shaft oil seal Used For Air Compressor single lip seal1616-6024-00 CCW ATLAS COP PTFE Stainless Steel Rotary Lip Oil Seal Air Compressor Shaft oil SealOS-G3210 lip seal atlas copco PTFE Rotary Shaft Seal lip seal for Germany air compressor1614950600 PTFE Oil Seals screw compressor oil seal pump shaft seal  Shaft Seal:   Prevent the leakage of high pressure liquid from the pump and prevent air from entering the pump.Although the position of the shaft seal in the pump is not large, but the normal operation of the pump is closely related to the shaft seal.If the shaft seal is selected improperly, not only in the operation of the need for frequent maintenance, leakage of a lot of liquid is conveyed, and may be due to the leakage of flammable, explosive and toxic liquid caused by fire, explosion and poisoning accidents, the consequences are unimaginable.Therefore, the shaft seal structure must be selected reasonably to ensure the safe operation of the pump. 1.Due to the atmospheric pressure with the outside world in cylinder, will inevitably make steam in cylinder or cylinder outside air along the radial clearance between shaft and cylinder leakage or leakage into, thereby causing loss to the working medium, the deteriorating operating environment, and heating shaft neck or make the steam into the bearing chamber, causes the deterioration of oil, leaking into the air and vacuum, thus increasing the extraction load, the unit will reduce the efficiency,To this end, the rotor through the cylinder at both ends are equipped with a seal, the seal is called the shaft end seal for short.High pressure shaft seals are used to prevent the leakage of steam out of the cylinder, and low pressure shaft seals are used to prevent the leakage of air into the cylinder. 2.Steam turbine operation is bound to have a part of the steam leakage from the shaft end to the atmosphere, resulting in the loss of working medium and heat, but also affect the turbine generator working environment, if the improper adjustment of steam leakage is too large, will make the bearing near the shaft seal temperature rise or make the bearing oil water.For this reason, in all kinds of units, set up the shaft seal heater, in order to recover the steam turbine shaft seal leakage 3.Prevent the steam in the cylinder and stem leakage outward, pollution of the turbine room environment and bearing lubricating oil quality.During the normal operation of the unit, high temperature steam flows through the turbine shaft and makes it heated, thus causing overtemperature of the bearing.The vacuum part of the cylinder that prevents air from escaping into the cylinder.Ensure the vacuum effect and vacuum degree of condenser when the unit is started.Recover seal and stem leaks to reduce working medium and energy losses. 4.In the steam turbine brake shutdown and the condenser needs to maintain a vacuum during the whole hot state shutdown process, to prevent air leakage into the steam turbine, accelerate the steam turbine internal cooling, resulting in bending of the shaft. Company Profile&Certifications:      Now over 100,000 quality filters including compressed air filters, Hydraulic Filters and complete filter housing assemblies at wholesale discounts. We offer OEM products as well as high quality replacements, engineered to precise OEM specifications and guaranteed to match the exact form, fit and function as the original equipment. Our company is committed to continuous innovation and further improvement to create, improve the efficiency and productivity of excellence, to achieve the highest level of reliabil