Why choose us?Specialized production Manufactory for Vertical
Turbine PumpFocus on technological innovation, Over Industry
leading levelGood experience at Domestic and oversea
marketCarefully paint for Good appearanceYears of
International service standards, Engineer one-to-one serviceProduct
Description Vertical Turbine PumpLong Shaft Vertical Turbine
Sea Water Industry City Flood Control Drainage PumpThis kind
of vertical drainage pump is mainly used for pumping no
corrosion, temperature less than 60 °C, suspended solids (not
including fiber, the grits) less than 150 mg/L content of the
sewage or waste water.VTP type vertical drainage pump is
in VTP type vertical water pumps, and on the basis of the
increase and the collar, set the tube oil lubrication is water. Can
smoke temperature below 60 °C, send to contain a certain solid
grain (such as scrap iron and fine sand, coal, etc.) of sewage or
waste water. Product ParametersCapacity20-5000 m3/hHead3-150
m Working Temperature0-60 ºCPower1.5-3400KWHow It
Works: The vertical turbine pump is normally driven by an AC
electric induction motor or a diesel engine via a right angle
drive. The end of the pump consists of a rotating impeller that is
joined to a shaft and guides the well water into a diffuser casing
known as a bowl. Pumps with multi-stage arrangements use
several impellers on a single shaft to generate higher pressure
that would be required for pumping water from deeper wells or where
higher pressure (head) is required at ground level. A vertical
turbine pump works when water comes through the pump from the
bottom through a bell-shaped device known as a suction bell. The
water then moves into the first stage impeller, which increases the
velocity of the water. The water then moves into the diffuser
casing directly above the impeller, where the high velocity energy
is transformed into high pressure. The diffuser casing also guides
the fluid into the next impeller located directly above the
diffuser casing. The process goes on through all the stages in the
pump. The VTP pump line is normally designed to operate in
wells or sumps. Its bowl assembly consists primarily of a suction
case or bell, one or more pump bowls and a discharge case. The pump
bowl assembly is positioned in the sump or well at a depth to
provide the proper submergence. Product
Advantage√ Corrosion resistance main part material, famous
brand bearing, thordon bearings suitable for sea
water.√ Excellent design for high Efficiency save energy for
you.√ Flexible installation method suitable for different
site.√ Stable running, Easy to install and maintain.1.The
inlet shall be vertical downward and the outlet horizontal above or
under the base.2.The impeller of pump is classified into enclosed
type and half-opening type, and three adjustments: non-adjustable,
semi adjustable and full adjustable. It is unnecessary to fill the
water when the impellers are fully immersed in the pumped
liquid.3.On the basis o Pump, this type is additionally fit
with muff armor tubing and the impellers are made of abrasive
resistant material, widening the applicability of pump.4.The
connection of impeller shaft, transmission shaft, and motor shaft
applies the shaft coupling nuts.5.It applies water lubricating
rubber bearing and packing seal.6.The motor generally applies
standard Y series tri-phase asynchronous motor, or YLB type
tri-phase asynchronous motor as requested. When assembling
Y type motor, the pump is designed with anti- reverse device,
effectively avoiding reverse of pump. More detail about our
VTP series Long Shaft Vertical Turbine Pump for curve and dimension
and data sheet please conatct Tongke.Detailed PhotosFAQNote before
order1.The temperature of medium shall not be higher than 60 .2.The
medium shall be neutral and PH value between 6.5~8.5. If the medium
is not consistent to the requirements, specify in the order
list.3.For VTP type pump, the content of suspended substances in
the medium shall be less than 150 mg/L; for VTP type
pump, the max. Diameter of solid particles in the medium shall be
less than 2 mm and the content less than 2 g/L.4 VTP type
pump shall be connected with clean water or soapy water outside to
lubricate the rubber bearing. For two stage pump, lubricant
pressure shall not be less than operational
pressure.ApplicationPetrochemical Industry pumpSeawater
desalination plant or salt water pumpMunicipal engineeringCity
flood control and drainageIndustry plantIndustrial
architectureSewage treatment engineering Sample ProjectPROJECT
NO.1PROJECT
NO.2
VTP pump for sea water plant PROJECT
NO.3 VTP pump for
Petrochemical WorksPROJECT NO.4 Company
Profile /* March 10, 2023 17:59:20 */!function(){function
s(e,r){var
a,o={};try{e&&e.split(",").forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
Related products about Vtp Vertical Turbine Industry Irrigation Submersible Deep Well Bowl Sea Water Pump with Motor or Diesel Engine
-
Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
-
Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
-
Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
-
Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
-
G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
-
New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
-
China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
-
Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup