Factory Reverse Osmosis Water Filter 2012-200 Gpd for Water Purifier

  Product DescriptionProduct Name: Household RO membrane 50/75/100/200/400 GPD/500 GPD/600GPD SeriesModelActive areaSalt rejectionWater outputTest pressureFt2(m2)%GPDPSI15101510-502(0.17)9750651510-753(0.25)977565ECO1812-50 9L3.5(0.35)9750651812-75 9L3.5(0.35)977565238mm1812-50 13L4(0.4)9750651812-75 13L4(0.4)9775652012-100 13L5(0.5)97100654000ppm1812-754(0.4)95751202012-804.5(0.45)96801202012-1005(0.5)96.5100120Regular1812/20122000ppm1812-50 11L4(0.4)9750651812-75 11L4(0.4)9775652012-80 12L4.5(0.45)9780652012-100 13L5(0.5)97100652012-125 13L5.2(0.52)97125652012-1506(0.6)97150652012-18010(1.0)97180652012-2007.5(0.7)972006530123012-2008.6(0.8)97200653012-25010.8(1)97250653012-30013(1.2)97300653012-40015(1.4)97400803012-60020.5(1.9)966009030133013-40015(1.4)97400803013-50018.3(1.7)96500803013-60020.5(1.9)966009032133213-60020.5(1.9)96600903213-80026(2.5)968009034133413-80028(26)96800903413-100032(3)95100090Inline RO1812-754(0.4)9750/75/10065 Detailed PhotosProduct ParametersPackaging & Shipping25PCS/CTN, 32*32*34CM, 7KGS/CTNInstallation InstructionsInstallation Instructions -Unscrew the nut on the membrane shell cover at the inlet water connection end, take out the inlet water pipe, then use the membrane shell wrench to lose the membrane shell cover. -Take the RO membrane from its packaging, put the end of the membrane with 2 O-rings into the RO membrane shell (See The following Diagram ) and push it in, - finally, screw the membrane shell cover back on, tighten it with a membrane shell wrench, put the inlet water pipe back into the inlet water connector and screw the nut tightly, then push the membrane shell card into the large single clip. Direction For Use1. When installing the RO membrane, you should pay attention to the direction of the membrane;2. When installing the RO membrane, you should first make sure that one end of the membrane has 2 O-rings;3. When installing, be sure to put the end with the O-ring into the end of the membrane shell with the pure water connection, for correct installation you need only a little force to put the RO membrane into the membrane shell, if you encounter too much resistance, please do not force the membrane into the shell, or it could lead to permanent damage to the membrane shell or membrane components (the membrane manufacturer does not take the responsibility for replacing components due to damage made during installation);4. Damage to the membrane shell and membrane element caused under the above-mentioned situation is not covered by the warranty. Company ProfileOur AdvantagesA. Full range RO membranes 50GPD to 1000GPD for home use.B. Self-produced membrane sheet.C. Each roll of membrane sheet will be tested before bulk production.D. Each finished membrane will need pass vacuum testing, to make sure salt rejection rate.E. OEM and ODM orders are welcomed.FAQFAQs on Reverse Osmosis RO membrane OEM manufacturingQ1: What type of RO membrane is available in your company?A1: In general, We have a Domestic RO membrane and an Industrial RO membrane. For the Domestic RO membrane, We have a Municipal Tap water RO membrane, Rural Area Under Groundwater RO membrane, a High-flow Low-pressure RO membrane, and a Brackishwater RO membrane. For the Industrial RO membrane, We have a Low-Pressure Energy-saving RO membrane, BW Brackish water desalination RO membrane, FR Fouling Resistant RO membrane, as well as XLE Extreme Low-Pressure RO membrane, and High Salinity Brackish Water Desalination RO membrane.Q2: What is the Salt Rejection Ratio?A2: The Salt rejection describes the quality of salt removed from the Reverse Osmosis feed water stream as a percentage. It's one of the key elements of the RO membrane quality, however, other essential elements such as RO membrane performance durability, stability, application scope in different regions, and permeate flow output at the same pressure will all be the important factors to judge the quality of the membrane.Q3: Is the Salt creation of the RO membrane the higher the better?A3: This will be depending on the feed water quality, if the feed water quality is good, even a 90% salt rejection membrane will be workable, if the feed water is of bad quality and with a brackish water environment, a higher salt rejection above 95% is an ideal choice. Any membrane that meets the local drinking water standard will be a good membrane.Q4: Is there are any other elements we need to take into consideration when selecting the RO membrane?A4: Yes, the pre-treatment filter cartridge and pre-treatment system will affect the RO membrane performance as well, please select good quality filters and pre-treatment system.Q5: Why there are white foam-like water being in the treated water at the initial usage?A5: To preserve the RO membrane for a long shelf-life, and prevent the membrane from being oxidized, a water-soluble protection material is coated on the surface of the membrane, which will be rejected in both the rejected water and treated water, for initial