12V 100Ah MF Battery Solar Dry Cell Battery Most Powerful Solar
BatteryProduct DescriptionNPS series descriptionTo cater for the
quick development of Solar applications in our life, based on
18-year experience in research and development, we succeeded in
designing NPS batteries mainly suitable for Solar / Wind power or
Photovoltaic system. That is why we call NPS batteries as PV
batteries too. In fact, this NPS Series batteries give excellent
cost efficient performance in Solar Energy System and it also been
promoted to other applications as Wind Power system, PV system,
golf cars, marine boats and so on. NPS series
Applications•Solar, PV & Wind Power Systems•Power Plants & Power
Transmission Systems•Golf Cars and Marine Boats•Vacuum Cleaner,
Lawn mower and other domestic applicances•EPS & UPS SystemsMain
Features♦Electrolyte Uniform DistributionNPS series battery is
manufactured with high-quality gaseous silica to make the
electrolyte in uniform distribution.♦No LeakageCurdled gaseous
silica used in Gel batteries can immobilize the electrolyte and
make the plates react evenly.♦Longer Cycle Service LifeDeep Cycle
design (high-density active material and thick plates) & special
4BS lead paste technology prolongs the cycle service
life.♦Excellent Deep Cycle AbilityUnique grid alloys & special
positive/negative lead paste formulations makes the battery perform
excellent in deep cycle using and recover quickly upon over
discharging and extend the float service life.♦Low Self
DischargeUsing high purity raw materials and gel electrolyte
ensures MCA batteries have less self-discharge.♦Environmental &
Non-pollutingGas Recombination technology ensures the battery high
seal reacting rate, which can prevent the acid fog from separating
out.♦Vibration resistantUsing GEL fixed with acid give battery a
high resistance to vibration. It also can be installed with an
inclined angle up to 180C.Batteries ListBattery ConstructionThe
Construction of a VRLA battery (all the batteries from our company
belong to VRLA battery) is shown above. The following is the
description of the different parts consisting of our batteries.1.
Plates (Electrodes)Plate construction is the Key to produce a good
battery. Recognizing this, Koyosonic utilizes the latest technology
and equipment to cast grids from a lead-calcium alloy free of
antimony. The small amount of calcium and tin in the grid alloy
imparts strength to the plate and guarantees durability even in
extensive cycle service. Lead oxide paste is added to the grid to
form the electrically electrically active material. In the charged
state, the negative plate paste is pure lead and that of the
Positive lead oxide. Both of these are in a porous or spongy form
to optimize surface area and thereby maximize capacity.2.
SeparatorsThe separator is made of woven glass fiber cloth with
high heat and oxidation resistance. The material further offers
superior electrolyte absorption and retaining ability, as well as
excellent ion conductivity.3. ElectrolyteImmobilized dilute
sulfuric acid: H2SO44. ContainerCase material is a ABS, a
high-impact proof plastic resin, Styrene, or a
polypropylene-polyethylene polymer with resistance to chemicals and
flammability. For 2V, 4V, 6V, 8V and 12V batteries, standard
container is manufactured from ABS plastic resin (UL94HB). It is
optional to use Flame Retardant ABS plastic resin (UL94V0). Each
cell has 2v in voltage and 4v battery has 2 cells. 6v battery has 3
cells, 8v battery has 4 cells and 12V battery has 6 cells. 5.
TerminalsDepending on the battery model, the terminals may be
Fastern type, bolt-and-nut type, pressure-contact type,
cable-and-connector type or other special types. Some are
threaded-insertion type or bolt-and-nut type.6. Relief ValveIn case
of excessive gas pressure build-up inside the battery (usually
caused by abnormal charging) the relief valve will open and relieve
the pressure. The one-way valve ont only ensures that no air gets
into the battery where the oxygen would react with the plates
causing internal discharge, but also represents an important safety
device in the event of excessive overcharge. Vent release pressure
is between 2-6 PSI and the seal ring material is neoprene rubber.7.
Case sealingThe case sealing is tongue and groove with polyrethane,
epoxy, or heat seal. The ABS plastic cover and container are sealed
by a special epoxy made in Japan and is acid
resistant. Packing PhotosOur CompanyKoyosonic Power Co
Ltd◊Koyosonic, established in 1999 has been specialized in
producing Lead-acid batteries, Li-ion batteries and Solar power
system. As one of professional manufacturers in lead acid
batteries, we have been devoted to research and development,
manufacture and market to lead the users to have right batteries
for their power system.Factory ViewCertificatesWelcome you contact
us for more business Cooperation. /* March 10,
2023 17:59:20 */!function(){function s(e,r){var
a,o={};try{e&&e.split(",").forEach(function(e,t){e&&(
Related products about 12V 100ah Mf Battery Solar Dry Cell Battery Most Powerful Solar Battery
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup