Automatic High Speed Corrugated Carton Box Printing Slotting Die Cutting Machine

Main technical parameters of CZXY series high-speed ink printing slotting machine  Inside width of wall platelmm2000Maximum paper sizemm700x1800Minimum paper sizemm170x450Effective printingmm700x1700Printing plate thicknessmm3-8Maximum speedSheets/min180Economic speedSheets/min150main motor powerKW4.0Registration accuracymm2 colors±1Slotting accuracymm±1.5Wall pate thicknessmm40Separate Sheet feedmm1850x850Dimension mm4000x3000x2000(LxWxH)  Feeding unitLead edge feeding & printing unit1.Machine separate and close(1)The electric control machine clutch is equipped with an alarm bell, and the alarm bell is continuously sounded during the movement to ensure the safety of the operators.(2)Pneumatic interlocking device.(3)The main motor adopts frequency conversion motor, frequency conversion control, energy saving, stable starting, with motor starting protection device.2.Leading edge roller paper feeding system(1)Suction assists paper feeding, and the air volume can be adjusted according to the different bending conditions of the cardboard to ensure smooth paper feeding.(2)Paper lifting and dropping are driven by air cylinders, which are quick and labor-saving.(3)Adopt the leading edge roller paper feeding system.(4)Manual adjustment of the side baffle and rear baffle box position; manual adjustment of the front baffle gap.(5)Interleaved paper feeding device (continuous or interleaved paper feeding can be selected as required).(6)The paper feed counter sets and displays the production quantity.3.Dust removal device (optional)(1) The brush dust removal device of the paper feeding part can remove a large amount of impurities on the printing surface of the cardboard and improve the printing quality.4.Paper feed roller(1) The outer diameter of the upper roller is φ100mm.(2) High-quality seamless steel, wrapped with wear-resistant rubber, and balance correction.(3) The lower roller is embossed with φ124mm and is plated with hard chrome, and the balance is corrected.(4) Manual adjustment of the paper feed roller gap dial, the adjustment range is 0-12mm.5.Auto-zero device(1) The paper feeding section, printing section, and slotting section are automatically reset to zero by electric.(2) Generally, the carton uses an automatic zero-return device, and it can be adjusted to the correct position after two trial printing, reducing the waste of cardboard.Host control: the motor image represents the switch state of the main motor, the current speed is displayed on it, and the fixed speed is the set speed. When the host is stopped, after filling in the number, turn on the host and run at the set speed. There are two paper feeding modes [ Continuous] [Alternative Sheets], click the paper feeding mode to switch, counting control; for the production of paper counting, the actual count = the set number, and then alarmBaffle control; manual adjustment of left and right, up and down Printing department (optional 1-5 color printing group)1. Printing roller (plate roller)(1) The outer diameter is φ240mm(2) The surface of the steel pipe is ground and plated with hard chromium.(3) Perform balance correction to ensure stable operation.(4) Load and unload the printing plate, the foot switch electrically controls the forward and reverse rotation.2. Printing press roller(1) The outer diameter is φ124mm.(2) The surface of the steel pipe is ground and plated with hard chromium.(3) Perform balance correction to ensure stable operation.(4) Manual adjustment of the printing press roller gap dial, the adjustment range is 0-12mm.3. Paper feeding upper and lower rollers(1) Upper roller: Thick-walled steel pipe with outer diameter of φ71mm, equipped with two paper feeding rings.(2) Lower roller: thick-walled steel pipe with outer diameter of φ124mm, surface ground, hard chrome plated.(3) Manual adjustment of the paper feed roller gap dial, the adjustment range is 0-12mm.4. Steel anilox roll (optional Dalian or Haili)(1) The outer diameter is φ140mm.(2) The surface of the steel pipe is ground, reticulated, and plated with hard chromium.(3) Perform balance correction to ensure stable operation.(4) The number of meshes can be selected from 180, 200, 220, 250, 300 meshes.(5) Cooperate with the pneumatic automatic lifting device of the paper feeding system. (The anilox roller descends to contact the printing plate during paper feeding, and the anilox roller rises and separates from the printing plate when paper feeding is stopped).(6) The anilox roller is equipped with a wedge-type overrunning clutch, which is convenient and quick to distribute and wash the ink.5. Rubber roller(1) The outer diameter is φ142mm.(2) The surface of the steel pipe is wrapped with wear-resistant rubber, and the balance is adjusted.(3) The rubber medium and high special grinding, the ink transfer effect is good.6. Phase adjustment mechanism(1) Planetary gear structure.(2) Motorized digital 360° adjustment of printing phase. (Adjustable for operation and stop)(3) Manually adjust