I,Main technical parameters
ItemunitLK-1370Voperating rangeX-axis travel (left and
right)mm1300Y-axis travel (front and rear)mm700Z-axis travel (up
and down)mm650Distance from worktable to spindle end
facemm120-700Distance from the front end of column to the center of
main shaftmm680WorkbenchTable area (L * W)mm1400*700maximum
loadkg800T-groove (width * spacing * number of grooves)mm18T*110*6X
/ Y / Z axis rapid feedm/min30*30*30Spindle specificationSpindle
speedrpm10000/12000Taper hole form and installation
sizekgBT40∮150Transmission mode (1:1)mmBeltRecommended motor
parameters for spindlekW15Accuracy (x / Y / z)positioning
accuracymm±0.003/300Repeated positioning accuracymm±0.003/300Other
informationThree axis powerkw2*2*3system FANUC --- can change
to Siemens 828DTool magazineT24Machine size floor space (L * w*
h)mm3650*2750*2850Pressure sourcekg/cm²6-7Power
capacityKva20machine weightkg9200II. Structural performance of
machine tool 1. Fuselage design The fuselage and saddle are
reinforced by mountain shaped ribs, with the shortest force
streamline, ensuring the best rigidity of the fuselage. Based on
the excellent engineering design, the stiffeners of the base and
column of the machining center can resist the torsion and damping,
and transfer the cutting vibration to non Cutting area. The column
is designed with torque tube, which can provide excellent rigidity,
bending and torsion resistance Ultra wide base design, At the same
time, lower the center of gravity of the base and adjust the center
of gravity of the machine tool to the best stable height. The span
at the bottom of the column is widened to improve the stability of
the machine tool. 2. spindle head The contact length ratio between
the main shaft and the column is appropriate to provide stable
support for the main shaft. Independent cooling system is built in
the spindle head to stabilize the spindle continuously The head
heat is in a reasonable range, which reduces the thermal extension
of the spindle and ensures the machining accuracy. 3. counterweight
In response to the processing requirements of different models, the
following counterweight methods are adopted: Counterweight: low
failure rate and long service life; Nitrogen counterweight: rapid
action, no noise, greatly improved processing accuracy, increased
machine life; No counterweight: in order to meet the requirements
of high speed and high sensitivity processing, the machine tool
adopts the method of no counterweight, and enhances the
requirements of servo motor and screw, Z-axis with brake, to ensure
the accuracy of the machine tool is stable and lasting, and
increase the service life. 4. screw rod It adopts imported grinding
level pre drawn double nut screw rod to eliminate reverse
clearance. After heat treatment, it has high rigidity, wear
resistance, torsion resistance and long service life, which
guarantees high machining accuracy of the machine. 5. AC servo
motor Adopt original imported from Japan, super high performance
servo motor, provide stronger power when heavy cutting. In the case
of low feed, high torque can still be maintained. Higher than 10000
(pixel) resolution and closed-loop position feedback ensure high
accuracy. High quality coupling ensures that the screw rod moves
with the axis of the motor. 6. Lubrication system The whole machine
adopts a positive displacement lubrication system and a de
pressurized oil pump, with stable pressure and flow, which
effectively transports the oil to each lubrication point and
provides uniform forced lubrication for each slide surface, so as
to ensure the accuracy and service life of the machine tool.
Chip remover system III. functions of CNC system CNC system
is Mitsubishi or FANUC system. Equipped with RS232C interface, with
data transmission function. Three axis simultaneous movement
Minimum instruction unit: 0.001mm Fast displacement speed
adjustment Feed rate adjustment Suspend Automatic origin reset G28
Second origin reset G30 Hand artery wave generator Workpiece
coordinate system G54-G59 Drilling fixed cycle G73, G76, g81-g89 /
g80 Rigid tapping g84, G74 Air run Emergency stop MDI function
Selective single node skip Single section implementation Program
suspension Manual control function: manual rapid feed, inching
feed, hand wheel feed Tool length correction G43, g44 / G49 Tool
radius correction G41, G42 / G40 Memory compensation of pitch error
Back gap correction Arc interpolation Linear interpolation Screw
interpolation Search for program number and serial number Sub
process call Conversion of public and British system Transmission
interface, DNC capacity Different alarm display Ladder diagram
display Macro programs and variables Mirror function Simple program
graphic display function NC control language: Chinese, English,
Japanese and other five languages are optional Monitoring function:
full coordinate display, spindle speed display, spindle load
display, PLC ladder circuit monitoring Protection function: over
Related products about CNC Control Mitsubishi M80A Fanuc Alpha Beta System Vertical Machine Center Lk-1370V
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup