Aluminum Alloy Forgings Tube Pipe Ring Flanges (6060/6061/6063/6066/6082/6110/6401)

Aluminum Alloy Forgings tube pipe ring flanges (6060/6061/6063/6066/6082/6110/6401) 6060/6063 aluminum alloy forgings  tube pipe ring flanges The application of 6060/6063 alloy (EN AW 6060/6063, AlMgSi/AlMg0.7Si) in the state of T5/T6. 6060 alloy composition: 0.30~0.60Si, 0.10~0.30Fe, 0.10Cu, 0.35~0.60Mg, 0.05Cr, 0.15Zn, 0.10 Ti, other impurities 0.05, 0.15, the rest Al, developed by the European Aeronautics and Astronautics Association, and registered in Alcoa in 1972. 6063 alloy components: 0.20~0.6 Si, 0.10~0.35Fe 0.10, Cu, 0.10Mn, 0.45~0.9Mg, 0.10Cr, 0.10Zn, Ti 0.10 and other impurities each 0.05, a total of 0.15, the rest is Al; 1945 to finalize the design, by the Alcoa Corp research and development, is currently the largest output single deformation Aluminum Alloy, mainly used for extrusion of aluminum construction, the building is 92% aluminum extrusion the above alloy production.The two alloys are characterized by excellent formability, solderability, corrosion resistance, suitable for electrochemical polishing and anodizing, and used for making highly decorative forgings.Specification of 6060/6063 aluminum alloy forgings  tube pipe ring flanges Alloy: 6060, 6063Available Temper: H112,O,F,T3,T4,T5,T6,T7,T8,T9,T651,T851,T451,T351Maximum single unit weight: 800kgMaximum  diameter with quenching:2000mmMaximum  diameter without quenching: 2800mm 6061 (ENAW6061, EN AW AlMgSiCu alloy) belongs to aluminum - magnesium - silicon - copper, finalized in 1934 by the Alcoa Corp, R & D, its chemical composition: 0.40~0.60 Si, 0.70Fe 0.15~0.40, Cu, 0.15Mn, 0.8~1.2, Mg, 0.04~0.35Cr, 0.25Zn, Ti 0.15, each of the 0.15 other impurities, the rest of the comprehensive performance of Al. alloy good corrosion resistance, strong corrosion resistance to seawater, his treatment can enhance the Aluminum Alloy are higher than other commonly used heat, good solderability, but deformation in cold working condition is not satisfied with the application in T5 and T6 under the condition of high under static and dynamic load capacity and its strength is much higher than that of 6063 alloy, used for the manufacture of high strength complex shape forging.Specification of 6061 aluminum alloy forgings  tube pipe ring flanges Alloy: 6061Available Temper: H112,O,F,T3,T4,T5,T6,T7,T8,T9,T651,T851,T451,T351Maximum single unit weight: 800kgMaximum  diameter with quenching:2000mmMaximum  diameter without quenching: 2800mmThe 6066 alloy is the American alloy in the late 1940s. It belongs to the Al-Mg-Si-Mn system alloy. Its components are 0.9~1.8 Si, 0.50Fe, 0.7~1.2 Cu, 0.6~1.1 Mn, 0.8~1.4Mg, 0.40 Cr, 0.25Zn, 0.20 Cr, and other impurities 0.05 0.05, a total of 0.15. Its high content of Si, in addition to the formation of Mg2Si strengthening phase, can also form the four element complex of AlSiCuMn phase and there is a considerable number of free Si, so there is a very good comprehensive mechanical properties, the mechanical properties of Forgings: minimum tensile strength and yield strength of Rm440N/mm - Rp 400N/ mm -., extension the rate of A 8%, Bush HBW. / hardness 115. Apply in T5 or T6 state. It has good machinability, and the ability to withstand static and dynamic loads is higher than that of other 6*** alloy forged aluminum alloys. The automobile industry uses 6066 alloys to forge safety systems and suspension parts.Specification of 6066 aluminum alloy forgings  tube pipe ring flanges Alloy: 6066Available Temper: H112,O,F,T3,T4,T5,T6,T7,T8,T9,T651,T851,T451,T351Maximum single unit weight: 800kgMaximum  diameter with quenching:2000mmMaximum  diameter without quenching: 2800mm6082 alloy has been widely used in Europe (EN AW 6082, AlSiMgCu), used in the T5 or T6 state, in 1972 by the European Association of Aerospace Aluminum Association registered in the United States, its chemical composition: 0.7~1.3Si, 0.50Fe, 0.10Cu, 0.40~1.0Mn, 0.6~1.2Mg, 0.25Cr, 0.20 Zn, 0.10 Ti, each of the 0.05 other impurities. A total of 0.15, the rest is Al. The commonly used state is T5 or T6, which is widely used in the automotive industry. The alloy has high static and dynamic load capacity, high corrosion resistance, good machinability and much use for forging hydraulic and pneumatic parts.It is widely used to manufacture heavy stress forgings for automobiles, such as spherical joints and flanges, as well as safety systems and parts of the suspension system.Specification of 6082 aluminum alloy forgings  tube pipe ring flanges Alloy:6082Available Temper: H112,O,F,T3,T4,T5,T6,T7,T8,T9,T651,T851,T451,T351Maximum single unit weight: 800kgMaximum  diameter with quenching:2000mmMaximum  diameter without quenching: 2800mmThe 6110 alloy belongs to Al-Si-Mg-Cu series alloy. Its components are 0.7~1.5 Si, 0.8 Fe, 0.20~0.7 Cu, 0.20~0.70 Mn, 0.50~1.1Mg, 0.04~0.25Cr, 0.20 Ni, 0.30, 0.15, and other impurities, 0.05 for each, 0.15 for others. The characteristics of this alloy is the content of Si is higher than 6060, 6061 and 6063 alloy, Fe, Zn and other impurities allo