Product description:Model DX68 CNC hose crimping machine has
equipped with computer numerical control system, fast crimp and
good quality. This machine features high crimp accuracy, big force,
low noise and easy to operate. It makes the mould base division to
be more even through the double inclined plane eight-flap mould
seat equipped with a high accuracy guiding device. DX68 CNC hose
crimping machine is mainly used for crimping processing for high
pressure hydraulic hose assembly in the mechanical engineering. It
can also be used for crimping steel pipes, especially large pipes
and irregular shape pipes.This machine features small and portable
appearance, big force, low noise and easy to operate. The buckling
amount can be precise adjusted through a scale. It makes the mould
base division to be more even through the double inclined plane
eight-flap mould seat equipped with a high accuracy guiding
device.Installation and Operation1. Add sufficiently 70 liters of
Great Wall brand 46# anti-abrasion hydraulic oil. If the room
temperature is lower than 10ºC, 10% transformer oil is need to
add.Connect the electric source well as per the machine
requirements, to make the direction of the motor rotation to be
consistent with the rotation direction marking, and grounding
protection shall be done.2. Regulating the scaleThe scale is used
for regulating the amount of the buckling. When it is regulated
clockwise, the buckling amount will decrease, when it is regulated
anticlockwise, the buckling amount will increase. The scale is
connected together with oil cylinder end cover through three socket
head screws and three springs on the scale base. When using a hand
to pull the scale (vertical to the oil cylinder end cover
direction), the scale can flexibly leave from the oil cylinder end
cover. When releasing the scale, the scale will be recovered
relying on spring force. Before the machine is turned on, inspect
carefully if the scale telescoping is flexible and if the lead
connection is reliable.3. The primary scale is turned within 0 line
of the secondary scale, turn the machine on for test run, and
observe if all actions are normal. If when the piston conducts
reciprocating movement, there is a crawling phenomenon, the bleed
screw on the oil cylinder top shall be unscrewed for exhausting
air.4. Pressure regulationThe buckling pressure and opening mould
pressure will be regulated through two knobs at the back of the oil
cylinder (see figure), when it is regulated clockwise, the pressure
will increase, when it is regulated anticlockwise, the pressure
will decrease (The pressure has already been well regulated when
ex-factory).5. Operation Based on the size of the rubber hose
to be buckled, select suitable mould as per the technical parameter
reference table of the locking pipe and mount it on the mould base.
Regulated well the scale position as per the data in the data in
the table, the pipe locking can be done. After pipe locking, use a
vernier caliper to mease the outside diameter dimension of the pipe
sleeve after buckling to see if it meets the reference table data
of the parameter. If it does not meet the data, the scale shall be
precisely regulated until it meets the requirements. Because the
manufactures of the pipe sleeve are different, so, specific
dimension, material, hardness etc are certainly not the same. These
factors would result different influences on the pipe locking
result, therefore, the data in the table is only for reference, the
detailed data take the pressure test as the basis. NoticesWhen
buckling, make the joint to locate the mould center as much as
possible, the joint is not buckled on the hex nut. Prevent tool and
other foreign matter from entering the locking head. After the work
is finished for each time, the eight-block mould base must be made
to extend to the greatest extent, this can make the spring to be at
extension status. If not, the spring will be damage. When working,
the hand should not stretch into the locking head.The power supply
must be switched off when maintenance is done.Maintenance We will
provide a guarantee to keep the machine in good repair within 3
years from the day when the machine is purchased. All fitting
troubles will be free of charge repaired (or replaced if necessary)
during the guarantee period. The damage resulted from improper use
o accident damage does not belong to free of charge repair
range.The hydraulic oil in the oil tank should be frequently
checked, if oil amount is found to be insufficient, the oil shall
be timely supplemented. If the oil liquid is polluted, it shall be
filtered or replaced. The locking head shall keep internal
cleanliness. Avoid the foreign matters during processing to enter
into the locking head oil cylinder via the mould to affect the
normal use. Wipe out the foreign matters, which are brought by the
mould body in time when buckling the joint. Frequently fill
suitable grease into the mould body for lubrication. PromiseWe will
pro
Related products about Hot Selling Good Price High Pressure Hydraulic Hose Crimping Machine
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup