Products DescriptionReaction KettleMaterial:SS304, SS316L,
Titanium, Hastelloy, PTFE lined and other materials
Application ScopeFood industry:edible coloring matter, chocolate
coating, filling food, syrup, flavoring, various additive,
etc;Medicine industry: medical ointment, ointment, lotion, cream,
various vitamin, etc Chemical industry :concerned with product of
daily use: shampoo, detergent, cream, tooth paste, paraffin liquor,
hair dye, etc.Adhesive industry: rubber liquor, polyester sulfured,
silicone, hot-melt adhesive, polyurethane, etc. This equipment is
used in the process of
hydrolysis,neutralization,crystallization,distillation and
evaporation in pharmaceutical,chemical, food, light and other
industries. Basic Conditions for Fermentation TankThe mechanical
agitation fermentation tank is one of the common types used in the
fermentation plant. It uses mechanical agitators to completely mix
air and the mash, and make the oxygen dissolved in the mash, which
guarantees the enough supply of oxygen for microbial growth,
reproduction and fermentation. Several basic requirements needed to
make fermentation tanks as followed: 1, Fermentation tanks should
have suitable scale of diameter to height, whichis generally about
1.7 to 4, the longer the tanks are, the higher the utilization rate
of oxygen will be. 2, Fermentation tanks can bear certain pressure.
When fermentation tanks are normally working or being disinfected,
there will certain pressure (hydraulic pressure and
pneumaticpressure) and temperature in the tanks, so all of their
components must have certain strength to bear the pressure. 3, The
stirring and ventilating device in fermentation tanksmake thegas
and the liquid fully mixed to make sure that the fermentation broth
must dissolve oxygen. 4, Fermentation tanks should have sufficient
cooling area. Inthe process of microbial growth and metabolism, it
will release a lot of heat. So in order to control the temperatures
on different stages in the fermentation process, it should be
equipped with adequate cooling area. 5, Fermentation tanks must
minimize dead cornersto avoid accumulation of dirt, so it can be
thoroughly sterilized to avoid bacterial contamination. 6, The seal
of agitators should be tight to minimize leakage. Size Scale of
Fermentation TankThere is a certain scale of the size of each part
of the tank. The scale of height to diameter of the tank is about
1.7 to 4. Fermentation tanks usually are equipped with two sets of
agitators. The distance between the two sets of agitators (S) is
about three times as the diameter of the agitator. For large-scale
fermentation tanks or those that have high liquid depth (HL), they
can install three or more sets of agitators. It will be better if
the agitator at the bottom is close to the exit of air dust, and
the distance to the bottom of the tank (C) equals to the diameter
of the agitator (Di), but could not be less than 0.8 times of Di,
otherwise it will affect the cycle of liquid. Technical parameters
of fermentation tankNominal Volume(m³)Diameter of internal
tank(mm)Mixing shaft rotational speed(rpm)Mixing shaft
power(kw)101800160-26017-22152000160-26020-30............2004600140-240215-360Technical
parameters of fermenting and seeding tank Nominal
Volume(m³)Diameter of internal tank(mm)Inner tank height(mm)Mixing
shaft rotational speed(rpm)Mixing shaft
power(kw)0.05300700300-3500.550.1400800300-3500.75-1.10.25001000280-3400.75-1.5...............5.014003200180-2207.5-18.5Design
/ Calculation SoftwareCustom ServiceOur Products for pharmaceutical
and chemical industries1. Multifunctional "Three in One"
(filtering, washing and drying) 2. Crystallizing Tank, Reaction
Kettle3. Sterile double-cone dryer4. Rake Vacuum Dryer /Paddle
Vacuum Dryer5. Plate-fin Heat ExchangerOur advantage1. Special
Equipment: Pressure Equipment, Equipment made of anti-corrosion
materials, Sterile EquipmentEquipment made of anti-corrosion
materials includes: anti-corrosion lining plastic/ PTFE/ enamel,
Ti/HC22/Mone112.Customized Design: Double-Cone in 20L-20m³Rake
Dryer (with mechanical seal) in 16 m³DN300-DN600 "Three in One"
3.Design/Calculation SoftwareScope of business1. On-site Inspection
2. Technical Innovation Plan for Equipment Technical Improvement
Plan for Equipment's Structure Optimization Fast and Effective
Solution to Equipment Malfunctions Highly Efficient and Precise
On-site Construction Service Commitment to a Deadline in
Customization A Full Range of long-term on-site technical
maintenance service3. Maintenance 4. Technical Solutions 5.On-site
Testing and Training 6. Spare PartsCompany Profile /*
March 10, 2023 17:59:20 */!function(){function s(e,r){var
a,o={};try{e&&e.split(",").forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
Related products about Leading Manufacturer and Supplier Seeding Tank High Pressure Chemical Mixing Reactor
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup