Product Descriptionaac wall panel equipment for aerated
autoclaved concrete aac wall panelMain raw materials of AAC are
siliceous material (sand, fly ash and Silicon tailings) and Calcium
materials (lime and cement) mixed with foaming agent (aluminum
powder). It is the product of light porous silicate through the
following processes: batching, mixing, pouring, hardening, cutting,
autoclaving and curing etc. Because of large amount of
well-distributed tiny pores after foaming, it is named autoclaved
aerated concrete.Main Features1. Light weight, can reduce the
building's own weight and cost, and help improve the earthquake
resistance of buildings2. Good thermal insulation performance and
low thermal conductivity3. It has processability. It has the
same processability as wood. It can be sawed, planed, drilled and
nailed, which is conducive to construction
and can be operated on site.4. Strong pressure resistance5.
Resistant to high temperature, and the compressive strength of the
aerated concrete is slightly increased when
the temperature is below 600 °C. When the temperature is around 600
°C, the compressive strength is close to the
compressive strength at normal temperature,
so The fire performance of aerated concrete for building materials
meets national first-class fire protection
standards.Gas block wall panel pictures and photos What
machine produce Gas block wall panel ? as following:Main
Process Flow of Gas block wall panel Production Line:1. Dose
and match measured raw materials;2. After distributing, feed raw
material into pouring mixer to make slurry.3. Through thoroughly
mixing, the slurry is poured to mould4. After pre-curing under
a certain temperature and time, the block would reach
a certain hardness and prepare for cutting;5. Tilting hoister
would turn over 90 degrees of mould;6. Then open the mould and
separate it from block. And take the block with side plate to the
cutting cart;7. The horizontal cutting machine cuts
blocks from both sides.8. Then the vertical cutting;9.
After cutting, the block is hanged to curing carts with side plate
by semi-finished product hoister;10. Grouping the carts and put
them into autoclaves;11. Curing the blocks under certain
temperature and pressure;12. Carry the finished product out of
autoclave by the winch.13. The finished product hoister take the
finished product to finished blocks area;14. The side plate return
back through side plate roller;15. Side plate would be organized
with open mould for the next circle.Detailed
Photos 1. Gas
wall panel Ball Mill: grinding sand to
slurry TypeDiameterLengthProductivityFeeeding
sizePower(KW)Φ1200x4500mm1200mm4500mm3-4t/h≤20mm55KWΦ1500x5700mm1200mm5700mm6-8t/h≤20mm130KWΦ1830x7000mm1830mm7000mm8-17t/h≤20mm245KWΦ2200x9000mm2200mm9000mm12-70t/h≤20mm380KW2. Gas wall
panel Slurry Pouring Mixer: To mix the standard sand
,slurry,lime,cement and aluminium paste into balance after
measuring Mixer typeMotor powerMixer drum volumeBlade
diameterBlade speedDiversion drum
type30kwV=3.6m3Φ560mm560r/minDiversion drum
type37kwV=4.5m3Φ630mm560r/min 3. Gas
wall panel Mould: storage sand slurry to
curingSize of (mm)Size of body(Peeling-off size)Maximum
overall
sizeLength(mm)Width(mm)Heigth(mm)Length(mm)Width(mm)Heigth(mm)4200x1200x600420012006004720173510784800x1200x600480012006005320173510786000x1200x600600012006006550175010854. Cutting
machine a: Horizatal cutting machineSizeMin spacing of
wiresRange of swing(mm)Diameter of cutting wire(mm)Overall
sizeLength(mm)Width(mm)Height(mm)4.2x1.2x0.6m10mm7.5Φ0.6-Φ1.05200320035604.8x1.2x0.6m10mm7.5Φ0.6-Φ1.05900320035606.0x1.2x0.6m10mm7.5Φ0.6-Φ1.0720032003560b:
Vertical cutting machineSizeMin spacing of wiresDiameter of cutting
wires(mm)Overall size(mm)diameter of wires(mm)For side
trimming(mm)Length(mm)Width(mm)Height(mm)4.2x1.2x0.6m5mmΦ0.6-Φ0.8Φ0.85500286025004.8x1.2x0.6m5mmΦ0.6-Φ0.8Φ0.85500286025006.0x1.2x0.6m5mmΦ0.6-Φ0.8Φ0.86500286025005. Gas
wall panel Hoist: hoist block mould and groupingsizeLifting
capacity(T)Moving speed(m/min)Lifting stoke(mm)Overal
sizeLength(mm)Width(mm)Height(mm)4.2x1.2m10t10-40m/min1350-17007700270028504.8x1.2m10t10-40m/min1350-17008300270028506.0x1.2m15t10-40m/min1350-170010500270028506. Gas
wall panel AutoclaveAutoclave Size(m)Autoclave Volume(m3)Mould
size(m)Mould volume(m3)Mould QTY
/ AutoclaveΦ2.0x3197.34.2x1.2x0.63.02414Φ2.0x26.583.24.2x1.2x0.63.02412Φ2.68x31174.84.8x1.5x0.64.3218Φ2.68x32180.46.0x1.2x0.64.3215Φ2.85x32204.16.0x1.5x0.65.415 Packaging
& Shipping AAC wall
panel making machine packaging & shipping
Our FactoryShandong Hongfa Machinery Co., Ltd is
a construction and building materials equipments manufacturer
mainly produce all kinds of AAC block making machine, concrete
mixing plant, mixer, concrete block making machine, concrete tile
making machine and concrete pipe making machine with more than 20
years experience and being the biggest manuf
Related products about AAC Wall Panel Equipment for Aerated Autoclaved Concrete AAC Wall Panel
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup