5t Small Single Punching Machine Household Milk Powder Tablet, Chinese Medicine Powder, Pellet Pressing Machine Equipment

Single punching tablet pressing machine will powder granular raw materials into 5-10mm diameter round sheet, cylindrical tablet, can also be pressed with text, trademark, pattern tablet. Tablet weight, thickness and hardness can be adjusted, as long as the change of different molds can be pressed different products, can be widely used in pharmaceutical factories, chemical plants, hospitals, scientific research units, laboratories and small batch production.Scope of applicationThis machine is widely used in pharmaceutical factory, pharmaceutical factory, biological engineering, food factory, health products factory, chemical factory, pharmaceutical factory, veterinary pharmaceutical factory and so on. The machine has wide adaptability to materials and good adaptability to non - adhesive powder.Pharmaceutical industry: Chinese medicine tablets, Western medicine tablets, nutrient tabletsFood industry: Candy chips, coffee chips, throat lozenges, chocolate beans, flavoring blocksHealth products industry: oral lozenges, milk tablets, calcium tablets, propolis tabletsElectronic battery industry: electronic components, button batteriesChemical industry: mothballs, aromatic balls, fertilizer tablets, mosquito coil incense tablets, catalysts, disinfection tablets, powderMetallurgical ceramic industry: catalyst, metallurgical powder particles, ceramic particles, metal sheets1. Tablet pressing method: electric tablet pressing or manual tablet pressing.2. Application scope: pharmaceutical tablets, food tablets, chemical tablets, pesticide tablets, veterinary drugs, etc.3. Tablet quality: tablet surface is smooth, tablet weight is uniform.4. Production capacity: 3500-4000 pieces can be produced per hour when electric pressing.5. Low raw material consumption (low experimental raw material consumption is only 200 grams).6. The weight, thickness and hardness of the tablet can be adjusted. As long as different molds are replaced, different products can be pressed.7. can be customized according to user requirements 5-10mm round mold.No professional operation technology, no professional and technical personnel, ordinary staff will learn, an operation can get 8.started, electric manual tablet, make the machine operation more simple.9. The tablet press is made of cast iron, and the mold is made of high hardness steel, which has a long service time.1 Prepare for installation1. The tablet press is installed on a firm wooden workbench (or can be installed on a cement workbench) and fixed with three M12 anchor screws. The height of the working table to the ground is about 600 mm (hand, easy to operate as the degree). In order to disassemble and repair easily, there should be a hole with a diameter of about 35 mm in the position of the lower core rod corresponding to the wooden work table.2. Before connecting the motor power supply, connect the motor with the ground wire to ensure safety. Remove the triangle belt, switch on the motor power supply, start the motor to observe whether the motor rotation direction is correct (the motor shaft rotation direction should be opposite to the direction of the arrow on the protective cover or hand wheel) if the rotation direction is not correct, then connect the cable and then install the triangle belt.3, the machine mold installation with pliers, tool wrench, hexagonal plate hand2. Installation of punching dieInstallation sequence: die, lower hopper Installation sequence: lower die -- middle die -- bench plate -- upper die -- lower hopper1) Lower die installationScrew the loose punching fixing screw, turn the hand wheel to raise the lower punching core rod to a high position, insert the lower punching rod into the hole of the lower punching core rod (make sure that the notched inclined plane of the lower punching rod is aligned with the lower punching fastening screw, and insert it to the end), and tighten the lower punching fixing screw.2) Middle die installationLoosen the fixing screw of the middle die, put the middle die flat into the hole of the middle die bench plate, at the same time make the lower punch into the hole of the middle die, press the bottom and tighten the fixing screw of the middle die. When placing the middle die, be careful to hold the middle die flat, so as not to get stuck and damage the hole wall when placing it askew.3) Upper die installationLoosen the upper punching fastening nut, insert the upper punching core rod into the hole of the upper punching core rod to the end, clamp the six sides of the lower part of the punching core rod with a wrench, tighten the upper punching fastening nut.After the die is installed, rotate the hand wheel to make the upper punch slowly drop into the middle die hole, and observe whether there is collision or friction. In case of collision or friction, loosen the fixing screw (two) of the middle die bench plate, adjust the fixing position of the middle die bench plate, and make the upper punch into the middle die hole, and then tighten th